浏览全部资源
扫码关注微信
纸质出版日期： 2024-07-25 ，
扫 描 看 全 文
周丹，高润凯，熊大辉，等.焊接速度对铝钢异种金属激光填丝熔钎焊性能的影响［J］.电焊机，2024，54（7）：76-82.
ZHOU Dan, GAO Runkai, XIONG Dahui, et al.Effect of Welding Speed on the Properties of Aluminum/Steel Dissimilar Metal by Laser Wire Fusion Brazing[J].Electric Welding Machine, 2024, 54(7): 76-82.
采用不同的焊接速度对铝合金E600及汽车车身
用镀锌钢板DP590D+Z进行激光填丝熔钎焊试验，焊接材料选用ER4047焊丝，分别对不同焊接速度下的焊缝成形质量、金属间化合物层厚度及力学性能进行了分析研究。结果表明：选择适当的焊接参数时，利用激光填丝熔钎焊可获得成形良好且具有一定抗拉强度的熔钎焊接头。为保证焊缝接头的性能，需控制界面处主要成分为FeAl
2
和FeAl
3
的金属间化合物层的厚度，随着焊接速度的提升，线能量下降，金属间化合物层厚度随之减小。综合考虑接头的线载荷及生产效率，最优焊接速度为1.5 m/min，此时线载荷约为197 N/mm，换算成铝合金强度为219 MPa，相当于母材强度的81%。
Aluminum alloy E600 and galvanized steel DP590D+Z for automotive body were tested by laser wire welding at different welding speeds. ER4047 wire was selected as welding material. The weld morphology
intermetallic compound layer thickness and mechanical properties were analyzed at different welding speeds. The test results show that the brazing joint with defects free and certain tensile strength can be obtained by laser wirefusion brazing with appropriate welding parameters. In order to ensure the performance of the weld joint
it was necessary to control the intermetallic compound thickness of FeAl
2
and FeAl
3
at the interface. With the increase of welding speed
the line energy and the intermetallic compound thickness decreased.On the basis of meeting the requirements of aluminum and steel dissimilar metal welding forming
the welding speed can be selected as far as possible to control the thickness and ensure the performance of the joint. Considering the linear load of the joint and production efficiency
the optimal welding speed was 1.5 m/min. The linear load was about 197 N/mm
and the converted strength of aluminum alloy was 219 MPa
which was equivalent to 81% of the strength of the base metal.
铝/钢激光填丝焊熔钎焊焊接速度金属间化合物
aluminum/steellaser wire weldingfusion brazingwelding speedintermetallic compound thickness
董显，董博文，程亚芳，等. 铝合金/钢异种金属激光熔钎焊技术研究进展［J］. 电焊机，2023，53（4）：25-33.
DONG X，DONG B W，CHENG Y F，et al. Research progress of laser brazing technology for dissimilar metals of aluminum alloy and steel［J］. Electric Welding Machine，2023，53（4）：25-33.
周丹，李翠，易鑫，等. 送丝速度对铝/钢激光填丝熔钎焊性能的影响［J］. 焊接，2019（3）：38-43.
ZHOU D，LI C，YI X，et al. Study on the influence of wire feeding speed on the properties of laser weld-brazing joints of aluminum/steel［J］. Welding & Joining， 2019（3）：38-43.
闫飞，周一凡，唐本刊，等. 铝钢异种材料激光搭接焊接头组织与性能研究［J］. 应用激光，2023，43（2）：66-69．
YAN F，Zhou Y F，Tang B K，et al. Microstructure and mechanical properties of aluminum/steel disssmilar laser lap welding joints［J］. Applied Laser，2023，43（2）：66-69.
陈鹏达，徐锴，徐玉君，等. 7A52铝合金中厚板MIG焊接工艺优化［J］. 电焊机，2023，53（1）：84-90.
CHEN P D，XU K，XU Y J，et al. Optimization on MIG welding processing parameters of 7A52 aluminum alloy medium-thickness plate［J］. Electric Welding Machine，2023，53（1）：84-90.
袁军军，李聪，甘瑞根，等. 铝/镀锌钢激光填丝熔钎焊对接接头的组织与力学性能［J］. 热加工工艺，2018，47（11）：71-75.
YUAN J J，LI C，GAN R G，et al. Microstructure and mechanical properties of wire feeding laser welding-brazing butt joint of aluminum/galvanized steel［J］. Hot Working Technology，2018，47（11）：71-75.
刘桂谦，汪永超，黄学飞，等. 钢-铝异种金属激光焊研究现状与展望［J］. 焊接技术，2022，51（12）：10-16.
LIU G Q，WANG Y C，HUANG X F，et al. Current status and prospect of laser welding of steel-aluminum dissimilar metal［J］.Welding Technology，2022，51（12）：10-16.
Albert F，Marben P，Graham T. Remote laser welding of steel and aluminum alloys［J］. Laser Technical Journal，2017，14（1）：32-35.
范霁康，马立，倪程，等. 5A01铝合金薄板激光摆动焊接接头微观组织与力学性能［J］. 电焊机，2023，53（1）：38-43.
FAN J K，MA L，NI C，et al. Microstructure and mechanical properties of 5A01 aluminum alloy sheet joint
welded by laser oscillation welding［J］. Electric Welding Machine，2023，53（1）：38-43.
高伟. 钢/铝异种金属对接接头光纤激光填丝熔钎焊研究［D］. 上海：上海交通大学，2014.
GAO W. Research on fiber laser wire fusion-brazing welding of steel-aluminum dissimilar butt joints［D］. Shanghai：Shanghai Jiao Tong University，2014.
冯菲玥，陈云霞. 铝钢异种金属焊接技术的研究现状［J］. 焊接技术，2021，50（1）：1-8.
FENG F Y，CHEN Y X. Research status of dissimilar metal welding technology in aluminum and steel［J］. Welding Technology，2021，50（1）：1-8.
高伟，阎启，黄坚. 钢/铝异种金属激光填丝熔钎焊对接接头组织与性能分析［J］. 中国激光，2014，41（6）：1-6.
GAO W，YAN Q，HUANG J. Microstructure and mechanical property of laser wire fusion brazing welded butt joints of steel/aluminum disssmilar metals［J］. Chinese Journal of Lasers，2014，41（6）：1-6．
孟圣昊. 基于界面调控的铝/钢异种金属激光填丝熔钎焊工艺及机理研究［D］. 黑龙江：哈尔滨工业大学，2017.
MENG S H. Research on process and mechanism of laser wire welding-brazing for Al/steel dissimilar metals based on interface control［D］. Heilongjiang：Harbin Institute of Technology University，2017.
王刚，曹雪龙，檀财旺，等. Ni/Si中间层对铝/钢激光焊接头组织与性能的影响［J］. 焊接学报，2020，41（4）：84-89.
WANG G，CAO X L，TAN C W，et al. Effect of Ni/Si interlayer on microstructure and properties of laser welded aluminum/steel joints［J］. Transactions of The China Welding Institution，2020，41（4）：84-89．
贾子妍，杨森，秦渊. 6061铝/Q235钢异种金属光纤激光焊接工艺研究［J］.应用激光，2019，39（3）：448-455.
JIA Z Y，YANG S，QIN Y. Dissimilar welding of Q235 to 6061 aluminum alloy by laser［J］. Applied Laser，2019，39（3）：448-455.
Dehghani M，Amadeh A，Akbari M S A A. Investigations on the effects of friction stir welding parameters on intermetallic and defect formation in joining aluminum alloy to mild steel［J］. Materials ＆ Design，2013，49：433-441．
陈夏明. 钢/铝激光深熔焊焊接接头组织性能研究［D］. 江苏：苏州大学，2019.
CHEN X M. Study on microstructure and properties of steel/Aluminum laser deep penetration welding joints［D］. Jiangsu：Suzhou University，2019.
彭聪，高向东，刘桂谦，等. 激光功率对高强钢DP780-铝合金5052异种材料焊接的影响［J］. 机床与液压，2021，49（7）：22-25.
PENG C，GAO X D，LIU G Q，et al. Effect of laser power on welding of High strength steel DP780-Aluminum Alloy 5052 dissimilar materialr［J］. Machine tool & Hydraulics，2021，49（7）：22-25.
Mohammadpour M，Yazdian N，Wang H P，et al. Effect of filler wire composition on performance of Al∕Galvanized steel joints by twin spot laser welding-brazing method［J］. Journal of Manufacturing Processes，2018，31：20-34.
王晓虹，谷晓燕，孙大千. 钢∕铝异种金属激光焊接头界面特性的研究［J］. 机械工程学报，2017，53（4）：26-33.
WANG X H，GU X Y，SUN D Q.Study on interface characteristics of Steel/Aluminum dissimilar metal laser welded joint［J］. Journal of Mechanical Engineering，2017，53（4）：26-33.
Das T，Das R，Paul J. Resistance spot welding of dissimilar AISI-1008 steel∕Al-1100 alloy lap joints with a graphene interlayer［J］. Journal of Manufacturing Processes，2020，53：260-274.
贾剑平，詹志平. 铝钢熔钎焊工艺及腐蚀性能研究进展［J］. 热加工工艺，2020，49（11）：1-5.
JIA J P，ZHAN Z P. Research progress on welding technology and corrosion properties of aluminum steel［J］. Hot Working Technology， 2020，49（11）： 1-5.
相关作者
相关机构
公网安备11010802024621