浏览全部资源
扫码关注微信
纸质出版日期： 2024-05-25 ，
扫 描 看 全 文
邓清洪.6063-T5铝合金散热器厚板搅拌摩擦焊工艺研究［J］.电焊机，2024，54（5）：85-91.
DENG Qinghong.Researched Friction Stir Welding Process of 6063-T5 Aluminum Alloy Radiator Thick Plate[J].Electric Welding Machine, 2024, 54(5): 85-91.
为探索大型宽幅翅片散热器铝合金厚板的FSW工艺，采用厚度为20.5 mm的6063-T5铝合金翅片散热器挤压型材作为试验材料，通过静龙门式二维生产型设备进行FSW。焊后利用光学显微镜、显微硬度仪和电子万能拉伸试验机对接头进行了金相分析、显微硬度分析和拉伸、弯曲力学性能测试。试验结果表明，在转速600 r/min，焊接速度140 mm/min的焊接工艺参数下，接头抗拉强度为158.0 MPa，为母材强度的87.7%；焊缝区相比母材有一定程度的硬度降低，接头存在两个明显的硬度软化区，分别是前进侧和后退侧热影响区，最低硬度值约33 HV；接头拉伸断裂方式为韧性断裂，接头弯曲到180°均不发生断裂。证明该FSW工艺可以获得表面成形良好、无宏观缺陷的焊接接头，其显微组织和力学性能测试结果满足工程应用要求。
To explore the Friction Stir Welding (FSW) process for large-width fin radiator aluminum alloy thick plates
20.5 mm thick 6063-T5 aluminum alloy fin radiator extrusion profiles were used as test materials and welded using a static gantry-type two-dimensional production equipment. Post-welding
the joints were analyzed and tested using an optical microscope
a microhardness tester
and an electronic universal tensile testing machine for metallographic analysis
microhardness analysis
and tensile and bending mechanical property tests. The experimental results indicate that under the welding process parameters of 600 revolutions per minute (r/min) and a welding speed of 140 millimeters per minute (mm/min)
the tensile strength of the joints was 158.0 MPa
which is 87.7% of the base material's strength. The hardness in the weld zone was somewhat lower compared to the base material
with two distinct hardness softening areas present in the heat-affected zones (HAZ) on both the advancing and retreating sides
with the lowest hardness value being approximately 33 HV. The joints exhibited ductile fracture in tensile testing
and no fractures occurred when the joints were bent to 180°. This demonstrates that the FSW process can achieve well-formed
macroscopic defect-free welded joints
with microstructural and mechanical property results that meet the requirements for engineering applications.
6063-T5铝合金厚板搅拌摩擦焊焊接缺陷力学性能
6063-T5 aluminum alloythick plate friction stir weldingwelding defectmechanical property
张俊林，李冬晓，张斌，等. 铝合金厚板FSW接头组织特征与金属流动行为［J］. 塑性工程学报，2021（11）：95-101.
ZHANG J L，LI D X，ZHANG B，et al. Microstructure characteristics and metal flow behavior of aluminum alloy thick plate FSW joint［J］. Journal of Plasticity Engineering，2021（11）：95-101.
方远方，张华. 厚板5083铝合金搅拌摩擦焊接头沿厚度方向组织与力学性能［J］. 机械工程学报， 2022， 58（4）：94-101.
FANG Y Y， ZHANG H. Microstructure and mechanical properties of 5083 aluminum alloy friction stir welded joint of thick plate along the thickness direction ［J］. Journal of Mechanical Engineering，2022，58（4）： 94-101.
邓清洪，游菲，吴勇. 6063-T5厚板搅拌摩擦焊接头层状撕裂缺陷研究［J］. 电焊机， 2020， 50（08）：78-82.
DENG Q H， YOU F， WU Y. Study on lamellar tearing defect of 6063-T5 thick plate friction stir welded joint［J］. Electric Welding Machine，2020，50（08）：78-82.
颜泽钢. 焊后热处理对6063-T6铝合金搅拌摩擦焊组织性能的影响［J］.热加工工艺，2018，47（13）：223-226.
YAN Z G. Effect of post-weld heat treatment on microstructure and properties of 6063-T6 aluminum alloy friction stir welding［J］. Hot Working Technology， 2018，47（13）：223-226.
荆洪阳，丰琪，徐连勇，等. 6063-T6铝合金搅拌摩擦焊组织与力学性能研究［J］. 机械工程学报，2020，56（8）：13-19.
JING H Y，FENG Q，XU L Y，et al. Study on microstructure and mechanical properties of 6063-T6 aluminum alloy friction stir welding［J］. Journal of Mechanical Engineering， 2020， 56（8）： 13-19.
崔云龙，张世欣，刘桐.铝合金搅拌摩擦焊S线形成机制分析［J］.轻合金加工技术，2022，50（05）：48-53+59.
CUI Y L，ZHANG S X，LIU T. Analysis on the formation mechanism of S line in aluminum alloy Friction stir welding［J］. Light Alloy Fabrication Technology， 2022，50（05）： 48-53+59.
张航，宫文彪，赵立哲，等. 6082-T6铝合金搅拌摩擦焊“S”线的形成及其对接头组织性能的影响［J］. 热加工工艺，2020，49（23）：23-26.
ZHANG H，GONG W B，ZHAO L Z， et al. The formation of "S" line in Friction stir welding of 6082-T6 aluminum alloy and its effect on joint microstructure and properties［J］. Hot Working Technology，2020，49（23）：23-26.
周平，戴启雷，张元杰. S线微观形貌对搅拌摩擦焊接头力学性能的影响［J］. 热加工工艺，2019，48（21）：49-52+57.
ZHOU P，DAI Q L，ZHANG Y J. The influence of S line micro morphology on the mechanical properties of friction stir welded joints［J］. Hot Working Technology， 2019， 48（21）： 49-52+57.
李帅贞，韩晓辉，毛镇东，等. 焊前清理对铝合金厚板搅拌摩擦焊接头S线及性能的影响［J］.电焊机，2018，48（03）：80-85.
LI S Z，HAN X H，MAO Z D，et al. Effect of pre welding cleaning on S line and performance of friction stir welded joint of aluminum alloy thick plate［J］. Electric Welding Machine，2018，48（03）：80-85.
赵华夏，董继红，孟强. 7050高强铝合金搅拌摩擦焊典型宏观缺陷试验研究［J］. 精密成形工程， 2019， 11（6）：141-148.
ZHAO H X，DONG J H，MENG Q.Experimental study on typical macroscopic defects in friction stir welding of 7050 high-strength aluminum alloy［J］. Journal of Netshape Forming Engineering，2019，11（6）：141-148.
毛育青，柯黎明，刘奋成，等. 铝合金厚板搅拌摩擦焊焊缝疏松缺陷形成机理［J］. 航空学报，2017，38（3）：256-264.
MAO Y Q，KE L M，LIU F C，et al. Formation mechanism of weld porosity defects in friction stir welding of aluminum alloy thick plate［J］. Acta Aeronautica et Astronautica Sinica， 2017，38（3）：256-264.
Pankul G，Arshad N S，Noor Z K，et al. Investigation on the Effect of Tool Pin Profiles on Mechanical and Microstructural Properties of Friction Stir Butt and Scarf Welded Aluminium Alloy 6063［J］. Metals，2018，8（1）：74-74.
Umanath K，Palanikumar K，Sankaradass V，et al. Optimizations of friction stir welding process parameters of AA6063 Aluminium alloy by Taguchi technique［J］. Materials Today：Proceedings，2021，46（9）：4008-4013.
郭雪艳，刘家斌，刘菲菲. 6082-T6铝板搅拌摩擦焊根部弱结合缺陷的研究［J］. 现代机械， 2022（2）：94-97.
GUO X Y，LIU J B，LIU F F. Study on weak bonding defects at the root of 6082-T6 aluminum plate friction stir welding［J］. Modern Machinery， 2022（2）：94-97.
张贵锋，朱大恒，程若亮，等. 搅拌摩擦对接焊根部弱连接特征，成因及液相溶解消除方法［J］. 焊管，2020，43（11）：26-35.
ZHANG G F，ZHU D H，CHENG R L，et al. Characteristics， causes and elimination methods of liquid phase dissolution of weak connection at the root of friction stir butt welding［J］. Welded Pipe and Tube， 2020， 43（11）：26-35.
周平. 铝合金搅拌摩擦焊接头根部缺陷控制［J］. 焊接， 2021（11）：48-51.
ZHOU P. Root defect control of aluminum alloy friction stir welding joint［J］. Welding & Joining， 2021（11）： 48-51.
Ozan S. Effect of friction stir welding on the microstructure and mechanical properties of AA 6063‐T6 aluminum alloy［J］. Journal of Materials Science， 2020，51（8）：1100-1119.
Meengam C，Sillapasa K，Pratumwal Y，et al. Effects of Heat Dissipation from Friction Stir Welding to Microstructures of Semi-Solid Cast 6063 Al Alloy［J］. Key Engineering Materials，2021，6253：70-75.
编辑部网址：http：//www.71dhj.comhttp://www.71dhj.com
相关作者
相关机构
公网安备11010802024621