扫 描 看 全 文
贺巍亮，王伟，李华芳，等.旋转速度对静止轴肩搅拌摩擦焊温度场和应力场的影响［J］.电焊机，2024，54（1）：86-94.
HE Weiliang, WANG Wei, LI Huafang, et al.Effect of Rotational Velocity on Temperature and Residual Stress Field by Stationary Shoulder Friction Stir Welding[J].Electric Welding Machine, 2024, 54(1): 86-94.
针对3 mm厚的2024-T4铝合金，采用ABAQUS软件建立静止轴肩搅拌摩擦焊热源三维模型，分析2024-T4铝合金静止轴肩搅拌摩擦焊温度场和应力场的有限元模拟，研究了恒定150 mm/min焊接速度下，旋转速度从800 mm/min到1 200 mm/min对焊接接头残余应力的影响。结果表明：常规搅拌摩擦焊焊缝横截面高温区域呈现碗状分布，而静止轴肩搅拌摩擦焊呈类似于搅拌针形貌分布。相比于常规搅拌摩擦焊，静止轴肩可以获得更窄的搅拌区宽度，并且有效降低焊缝中心的峰值温度。焊后垂直于焊缝区域的纵向残余应力呈现“M”形分布，随着搅拌头旋转速度的增大，两种工艺下的焊后残余应力均增大。此外，静止轴肩在焊接过程中对焊缝区域持续碾压，使得焊后试样的纵向残余应力峰值相比较于传统搅拌摩擦焊能降低45.6%。
Based on 3 mm thickness 2024-T4 Alloys, the three-dimensional model for heat source of stationary shoulder friction stir welding is established by using numerical simulation software ABAQUS. The temperature and residual stress field distributions of stationary shoulder friction stir welding of 2024-T4 is analyzed, and the effects of rotational velocities ranging from 800 mm/min to 1 200 mm/min on residual stress were investigated in detail. The results show that the high temperature region of the cross-section appeared to be a bowl-shaped distribution, and the shape for the stationary shoulder friction stir welding was similar to the rotating pin. Stationary shoulder friction stir welding was beneficial to decreasing the peak temperature of stir zone and then obtaining a narrower area compared with conventional shoulder. The shape of the longitudinal residual stress in section perpendicular to the weld presented “M”after welding. The residual stress increased with the increase of rotational velocity under different processes. The stationary shoulder provided synchronous rolling during welding,which reduced 45.6% peak residual stress.
2024-T4铝合金静止轴肩搅拌摩擦焊旋转速度残余应力
2024-T4 alloysstationary shoulder friction stir weldingrotational velocityresidual stress
Daws C J. An introduction to friction stir welding and its development［J］. Welding & Metal Fabrication，1995， 63（1）：279-285.
Zhang C，Huang G，Cao Y，et al. On the microstructure and mechanical properties of similar and dissimilar AA7075 and AA2024 friction stir welding joints：Effect of rotational speed［J］. Journal of Manufacturing Processes，2019，37（11）：470-487.
董吉义，汤化伟，尹玉环，等. 搅拌摩擦焊接过程闭环控制方法研究［J］. 电焊机，2019，49（9）：99-102.
DONG J Y，TANG H W，YIN Y H，et al. Research on closed-loop control method of friction stir welding process［J］. Electric Welding Machine，2019，49（9）：99-102.
温时梅. 混联构型机器人钛合金/CFRP叠层构件螺旋铣孔质量优化研究［D］. 天津：天津大学，2018.
WEN S M. Research on Quality Optimization ofHybrid Robot Based Helical Milling for Titanium Alloy/CFRPStacks Structure［D］. Tianjin：Tianjin University，2018.
潘锐，王善林，李建萍，等. 工艺参数对搅拌摩擦焊变形铝合金接头性能的影响［J］. 焊接学报， 2016， 37（11）：89-92.
PAN R，WANG S L，LI J P，et al. Effect of processing parameters on mechanical properties of aluminum alloy joints welded by friction stir welding［J］. Transactions of the China Welding Institution，2016，37（11）：89-92.
王进军，王桂珍，刘鹏，等.2024铝合金搅拌摩擦焊接头组织结构及力学性能［J］.电焊机，2015，45（06）：86-90.
WANG J J，WANG G Z，LIU P，et al. Microstructure and mechanical properties of the friction stir welding joints of 2024 aluminum alloy［J］. Electric Welding Machine，2015，45（06）：86-90.
付文侦，贺地求，王海军，等. 静止轴肩搅拌摩擦焊技术研究现状［J］. 热加工工艺，2022，51（15）：7-13.
FU W Z，HE D Q，WANG H J，et al. Research Status of Stationary Shoulder Friction Stir Welding［J］. Hot Working Technology，2022，51（15）：7-13.
褚强，郝思洁， Devang Sejani，等. 静止轴肩搅拌摩擦焊接研究进展及展望［J］. 电焊机，2020，50（9）：44-52.
CHU Q，HAO S J， Sejani D，et al. Development and prospect of stationary shoulder friction stir welding［J］. Electric Welding Machine，2020，50（9）：44-52.
Khandkar M，Khan J A，Reynolds A P，et al. Predicting residual thermal stresses in friction stir welded metals［J］. Journal of Materials Processing Tech.，2006，174（1-3）：195-203.
李思潭，闫鹏庆，惠越. 搅拌摩擦焊参数对残余应力分布的影响［J］. 焊接技术，2021，50（11）：19-24.
LI S T，YAN P Q，HUI Y. Effects of friction stir welding parameters on residual stress distribution［J］. Welding Technology，2021，50（11）：19-24.
Huang X，Reynolds A P. Effects of the friction stir welding process variants on residual stress［J］. Science & Technology of Welding & Joining，2017，23（4）：279-286.
唐文珅，杨新岐，赵慧慧，等. 厚板铝合金静止轴肩搅拌摩擦焊热过程及受力状态数值分析［J］. 航空制造技术，2020，63（11）：41-49.
TANG W K，YANG X Q，ZHAO H H，et al. Numerical Analysis of Stationary Shoulder Friction Stir Welding Process for Aluminum Alloy Thick-Plate［J］. Aeronautical Manufacturing Technology，2020，63（11）：41-49.
吉华，徐萌，封小松，等. 静止轴肩搅拌摩擦焊T型接头组织及力学行为［J］. 电焊机，2013，43（09）：37-40.
JI H，XU M，FENG X S，et al. Research on microstructure and mechanical behavior of T-joint welded by stationary shoulder friction stir welding［J］. Electric Welding Machine，2013，43（09）：37-40.
Vicharapu B，Liu H，Fujii H，et al. Probing residual stresses in stationary shoulder friction stir welding process［J］. International Journal of Advanced Manufacturing Technology，2020，106（5-6）：1-14.
杨海峰，赵洪运，许欣欣，等. 静轴肩搅拌摩擦焊2A14-T4铝合金T形接头的组织和性能［J］. 材料导报，2021，35（20）：20045-20051.
YANG H F，ZHAO H Y，XU X X，et al. Microstructure and Properties of 2A14-T4 Aluminum Alloy T Joint by SSFSW［J］. Materials Reports，2021，35（20）：20045-20051.
Ji S，Li Z，Zhang L，et al. Effect of lap configuration on magnesium to aluminum friction stir lap welding assisted by external stationary shoulder［J］. Materials & Design，2016，103（8）：160-170.
赵俊，柯黎明，黄斌，等. 工艺参数对铝合金静轴肩搅拌摩擦焊焊缝成形的影响［J］. 热加工工艺，2019，48（13）：22-25.
ZHAO J，KE L M，HUANG B，et al. Influence of Process Parameter on Weld Formation of Stationary Shoulder Friction Stir Welding of Aluminum Alloy［J］. Hot Working Technology，2019，48（13）：22-25.
Li Z，Yue Y，Ji S，et al. Joint features and mechanical properties of friction stir lap welded alclad 2024 aluminum alloy assisted by external stationary shoulder［J］. Materials and Design，2016，90（1）：238-247.
张坤，方远方，栾国红，等. 静止轴肩搅拌摩擦焊接6005铝合金的力学和疲劳性能［J］. 焊接学报，2017，38（10）：25-28+130.
ZHANG K ，FANG Y F，LUAN G H，et al. Mechanical and fatigue property of stationary shoulder friction stir welding AA6005［J］. Transactions of the China Welding Institution，2017，38（10）：25-28+130.
Wu H，Chen Y C，Strong D，et al. Stationary shoulder FSW for joining high strength aluminum alloys［J］. Journal of Materials Processing Technology，2015，221：187-196.
贺地求，李生朋，李剑，等. 1.8 mm 2024-T4铝合金板的搅拌摩擦焊接［J］. 热加工工艺，2011，40（07）：112-114+117.
HE D Q，LI S P，LI J，et al. Friction Stir Welding of 2024-T4 Aluminum Alloy Plate with 1.8 mm Thickness［J］. Hot Working Technology，2011，40（07）：112-114+117.
Xu W，Liu J，Zhu H，et al. Influence of welding parameters and tool pin profile on microstructure and mechanical properties along the thickness in a friction stir welded aluminum alloy［J］. Materials & Design，2013，47（03）：599-606.
Threadgill P L，Leonard A J，Shercliff H R，et al. Friction stir welding Aluminium alloys［J］. International Materials Reviews，2009，54（2）：49-93.
Wang L，Davies C M，Wimpory R C，et al. Measurement and simulation of temperature and residual stress distributions from friction stir welding AA2024 Al alloy［J］. Materials at High Temperatures，2010，27（3）：167-178.
刘琪，董仕节，官旭，等. 搅拌摩擦焊温度场数值模型的研究进展［J］. 材料导报， 2015，29（21）：118-125.
LIU Q，DONG S J，GUAN X，et al. A Review of Numerical Model for Temperature Field in Friction Stir Welding Process［J］. Materials Review，2015，29（21）：118-125.
相关作者
相关机构
公网安备11010802024621