不同气氛对2219铝合金TIG焊接头组织和性能的影响
Effect of Different Shielding Gases on the Microstructure and Properties of 2219 Aluminum Alloy TIG Welding Joint
- 2023年53卷第12期 页码:95-100
DOI: 10.7512/j.issn.1001-2303.2023.12.15
扫 描 看 全 文
扫 描 看 全 文
杨康,唐瑜,汪鹏举,等.不同气氛对2219铝合金TIG焊接头组织和性能的影响[J].电焊机,2023,53(12):95-100.
YANG Kang, TANG Yu, WANG Pengju, et al.Effect of Different Shielding Gases on the Microstructure and Properties of 2219 Aluminum Alloy TIG Welding Joint[J].Electric Welding Machine, 2023, 53(12): 95-100.
氩弧TIG焊熔深浅、焊接效率低,难以适用于厚板2219铝合金的焊接。针对此问题,分别采用两面四层氩弧TIG焊工艺和氦弧TIG焊打底两面三层焊接工艺进行焊接,分析了不同工艺对接头组织和力学性能的影响。结果表明:氦弧打底的两面三层焊接接头与两面四层氩弧焊接头相比,由于打底层单次热输入量较大,焊缝过时效区硬度大幅下降,焊缝区等轴晶长大、θ相增多,因此虽然硬度、抗拉强度增大,但是延伸率明显降低。合适的焊接速度和电流可以细化接头处的晶粒,抑制第二相的析出和聚集,从而提高接头的力学性能。
In the paper, as the object, 15 mm thick 2219 Aluminum alloy are welded by TIG with helium and argon protecting respectively, and the effect of different processes on the structure and performance of the joints are analyzed. The results show that: compared with joints welded with argon protected, the joints welded with helium protected have a larger hardness in the over-aging zone, due to the larger single-time heat input in the bottom layer. The α grains in the weld area grow, and the θ-phase increase, which increases the hardness and tensile strength of the joint, but the elongation decreases significantly. Appropriate welding speed and current can refine the crystal grains and inhibit the precipitation of the second term at the joint, thereby improving the mechanical properties of the joint.
保护气体2219铝合金TIG焊接头组织力学性能
shielding gases2219 Aluminum AlloyTIG Weldingmicrostructuremechanical properties
CHEN S H, LI L Q, CHEN Y B,et al. Sidiffusion behavior during laser welding-brazing of Al alloy and Ti alloy with Al-12Si filler wire[J]. Transactions of Nonferrous Metals Society of China, 2010, 20(1): 64-70.
王志国,窦超,尹玉环,等. 2219铝合金搅拌摩擦焊焊缝夹杂的形成原因分析与控制[J]. 电焊机, 2019, 49(9):29-33.
WANG Z G,DOU C,YIN Y H,et al. Cause analysis and control of inclusion in 2219 aluminum alloy friction stir weld[J]. Electric Welding Machine, 2019, 49(9):29-33.
丁延松,曲文卿,李来平.2219铝合金FSW接头低温力学性能研究[J]. 电焊机, 2019, 49(1):85-88.
DING Y S,QU W Q,LI L P. Mechanical properties of FSW joint of 2219 aluminum alloy at low temperature[J]. Electric Welding Machine, 2019, 49(1):85-88.
张勤练,李钊,杨春利,等. 铝合金TIG 电弧横焊接头缺陷及控制[J]. 焊接学报,2017,38(2):28-32.
ZHANG Q L,LI Z,YANG C L,et al. Welding defects and its control in TIG Arc welding of aluminum alloys in horizontal position[J]. Transactions of the China Welding Institution,2017,38(2):28-32.
赵红星,王国庆,宋建岭,等. 氦弧与氩弧电弧特性对比研究[J].机械工程学报,2018,54(8):137-143.
ZHAO H X,WANG G Q,SONG J L,et al. Comparative Research of Helium and Argon Arc Characters[J]. Journal of Mechanical Engineering,2018,54(8):137-143.
唐瑜,杨康,林鹏,等.2219铝合金对接+搭接接头TIG焊接工艺研究[J].电焊机,2022,52(01):89-94.
TANG Y, YANG K, LIN P, et al. Study on welding process of 2219 aluminum alloybutt + overlap joints[J]. Electric Welding Machine, 2022, 52(01): 89-94.
周 政,王国庆,宋建岭,等. 2219铝合金不同气氛下TIG焊焊接接头组织性能[J].焊接学报,2018,39(7):47-50.
ZHOU Z,WANG G Q,SONG J L,et al. Microstructure and mechanical properties of 2219aluminum alloys TIG welding welded joints in different shielding gases[J]. Transactions of the China Welding Institution,2018,39(7):47-50.
孙世烜,张勤练,李延民,等. 2219 铝合金变极性TIG 横焊接头组织与性能研究[J].航天制造技术,2015(2):5-14.
SONG S H,ZHANG Q L,LI Y M,et al. Research on Microstructures and Mechanical Properties of Horizontal Position Welding Joints of 2219 Aluminum Alloy by Variable Polarity TIG[J]. Aerospace Manufacturing Technology,2015(2):5-14.
康举,李艳军,吴爱萍,等.两种 TIG 焊工艺对 LD10 接头力学性能的影响[J].焊接学报,2014,35(3):109-112.
KANG J,LI Y J,WU A P,et al. Effect of two different TIG welding processes on mechanical properties of LD10 aluminum alloy joint[J]. Transactions of the China Welding Institution,2014,35(3):109-112.
邱宇. 风塔用中厚钢板热处理工艺以及CTOD 断裂韧性研究[D]. 江苏:南京理工大学,2013.
QIU Y. Research on the heat treatments progress and the CTOD fracture toughness of thick steel plates used for wind towers[D].Jiangsu:Nanjing University of Science and Technology,2013.
编辑部网址:http://www.71dhj.comhttp://www.71dhj.com
相关作者
相关机构