316L和2205异种不锈钢等离子弧焊接头的微观组织和性能

张尧成; 范孜耘; 王振; 仲加文; 孟涛

doi:10.7512/j.issn.1001-2303.2023.10.13

焊接工艺 | 浏览量 : 0 下载量: 5 CSCD: 0

PDF
导出
分享
收藏
专辑

316L和2205异种不锈钢等离子弧焊接头的微观组织和性能
Study on the Microstructure and Properties of 316L-2205 Dissimilar Stainless Steel Joints Welded by Plasma Arc Welding
2023年53卷第10期页码：84-89
DOI： 10.7512/j.issn.1001-2303.2023.10.13

扫描看全文

张尧成，范孜耘，王振，等.316L和2205异种不锈钢等离子弧焊接头的微观组织和性能［J］.电焊机，2023，53（10）：84-89.

ZHANG Yaocheng, FAN Ziyun, WAGN Zhen, et al.Study on the Microstructure and Properties of 316L-2205 Dissimilar Stainless Steel Joints Welded by Plasma Arc Welding[J].Electric Welding Machine, 2023, 53(10): 84-89.
张尧成，范孜耘，王振，等.316L和2205异种不锈钢等离子弧焊接头的微观组织和性能［J］.电焊机，2023，53（10）：84-89. DOI： 10.7512/j.issn.1001-2303.2023.10.13.

ZHANG Yaocheng, FAN Ziyun, WAGN Zhen, et al.Study on the Microstructure and Properties of 316L-2205 Dissimilar Stainless Steel Joints Welded by Plasma Arc Welding[J].Electric Welding Machine, 2023, 53(10): 84-89. DOI： 10.7512/j.issn.1001-2303.2023.10.13.

摘要

采用等离子弧对3 mm厚的316L奥氏体不锈钢和2205双相不锈钢板进行对接焊，分析了焊接接头微观组织、力学性能以及耐腐蚀性能。结果表明，316L/2205异种不锈钢等离子弧焊焊缝组织总体均匀细小，但各区域具有一定方向性，焊缝组织随转弧电流增大而粗化，焊缝区的奥氏体和铁素体较粗大。不同大小电流下的异种不锈钢接头的显微硬度分布总体的变化趋势基本一致，焊缝平均抗拉强度达到533~571 MPa，且均断裂在316L侧。转弧电流较小时，焊缝细小均匀的组织保证了其较高的硬度和拉伸强度。两种母材和焊缝的自腐蚀电位从高至低为75 A焊缝>85 A焊缝>316L母材>2205母材>95 A焊缝。增大转弧电流可使焊缝中奥氏体含量增加且破坏晶界，从而影响晶间腐蚀速率。

Abstract

Plasma arc welding was adopted to butt welding of 316L austenitic stainless steel and 2205 duplex stainless steel, and the microstructure, mechanical properties and corrosion resistance of the welded joint were analyzed. The results showed that the microstructure of plasma arc welded 316L/2205 dissimilar stainless steel joints was uniform and fine, and being with a certain directionality. The size of austenite and ferrite in the weld zone was larger than that of in the edge area, but was coarsened with increasing the arc current. The overall change trend of the microhardness distribution of the dissimilar stainless steel joints under different currents was consistent. The average tensile strength of the welds reached 533~571 MPa, and all joints fractured on the 316L side. When the arc current was small, the fine and uniform microstructure of the weld ensured high hardness and tensile strength. The self-corrosion potential of the base materials and welds from high to low was joint 75 A > joint 85 A>316L base material>2205 base material>joint 95 A. Increasing the arc current can increase the austenite content in the weld and destroy the grain boundaries, thereby affecting the rate of intergranular corrosion.

关键词

等离子弧异种钢接头微观组织力学性能耐腐蚀性能

Keywords

plasma arcdissimilar steel jointmicrostructuremechanical propertiescorrosion resistance

references

李天庆，杨喜牟，雷玉成，等. 气流再压缩等离子弧焊接工艺初步探究［J］. 焊接学报，2019，40（11）： 28-32+162.

LI T Q，YANG X M，LEI Y C，et al. Preliminary study on gas stream recompressed plasma arc welding process［J］.Transactions of the China Welding Institution，2019，40（11）：28-32+162.

高杰，王娟，李亚江. 异种钢的焊接研究现状［J］. 精密成形工程，2017，9（5）：83-89.

GAO J，WANG J，LI Y J. Study on the Welding of Dissimilar Steel［J］. Journal of Netshape Forming Engineering，2017，9（5）：83-89.

郭韡，张康武，俞洪杰，等. 316L不锈钢搅拌摩擦焊与氩弧焊接接头组织性能比较［J］. 重型机械，2019，（1）：42-45.

GUO W，ZHANG K W，YU H J，et al. Comparison of FSW joints microstructure and properties to TIG 316L austenitic stainless steel［J］. Heavy Machinery，2019，（1）：42-45.

Bhattacharya A，Singla S. Mechanical Properties and Metallurgical Characterization of Dissimilar Welded Joints between AISI 316L and AISI 4340［J］. Transactions of the Indian Institute of Metals，2017，70：893-901.

王鑫. B-HARD360高强耐磨钢GMAW“低强匹配”焊接接头的强韧性研究［D］. 济南：山东大学，2016.

WANG X. Investigation of Strength-toughness of B-HARD360 High Strength Wear-resistance Steel Undermatched Joints by GMAW［D］. Jinan：Shangdong University，2016.

刘立伟，杨建炜，王凤会，等. Q345R/316L复合板埋弧焊接头组织及耐蚀性研究［J］. 焊接技术，2021，50（4）：29-33+105-106.

LIU L W，YANG J W，WANG F H，et al. Study on microstructure and corrosion resistance of submerged arc welding joint of Q345R/316L composite plate［J］.Welding Technology，2021，50（4）：29-33+105-106.

Zhang Y， Yang L，Lu W，et al. Microstructure and elevated temperature mechanical properties of IN718 alloy fabricated by laser metal deposition［J］. Materials Science and Engineering：A，2020，771：138580.

齐新瑞，郝辞，冷昊凯. 2205双相不锈钢焊接接头显微组织与力学性能研究［J］. 热加工工艺，2017，46（21）：165-167+172.

QI X R，HAO C，LENG H K. Study on Microstructure and Mechanical Properties of 2205 Duplex Stainless Steel Welded Joint［J］. Hot Working Technolog，2017，46（21）：165-167+172.

王晓军，杨健，周栋，等. Q345/316L异种钢K-TIG焊接接头的组织及性能［J］. 电焊机，2021，51（1）：66-72+121.

WANG X J，YANG J，ZHOU D，et al. Microstructure and properties of K-TIG welded joint of Q345/316L dissimilar steel［J］. Electric Welding Machine，2021，51（1）：66-72+121.

高心心. 异种高强钢焊接接头腐蚀及氢脆性能研究［D］. 山东：青岛科技大学，2017.

GAO X X. Study on Corrosion and Hydrogen Embrittlement of Dissimilar High Strength Steel Welded Joints［D］. Shandong：Qingdao University of Science & Technology，2017.

张晓柏，唐小华，罗昌森，等. 敏化处理对CHS2209双相不锈钢焊条熔敷金属晶间腐蚀的影响［J］. 热加工工艺，2018，47（12）：191-194.

ZHANG X B，TANG X H，LUO C S，et al. Effectof Sensitization on Intergranular Corrosion of Deposited Metalof CHS2209 Duplex Stainless Steel Electrode［J］. Hot Working Technolog，2018，47（12）：191-194.

文章被引用时，请邮件提醒。

提交

大轴向力低转速2219铝合金拉塞焊工艺探究及接头性能分析

2A14铝合金VPTIG焊交叉焊缝组织与力学性能

TC4钛合金激光-MIG复合焊接头组织性能

热场辅助电磁脉冲焊接Al/Cu异种金属接头组织性能研究

超大离焦量对TRIP800高强钢激光焊接接头微观组织与力学性能的影响