活性剂对激光焊熔池动态行为的作用机理研究

佘昆; 李冬辉; 元育学; 黄一鸣; 杨立军; 伍倍乐

doi:10.7512/j.issn.1001-2303.2023.09.14

人机协作智能焊接 | 浏览量 : 0 下载量: 20 CSCD: 0

PDF
导出
分享
收藏
专辑

活性剂对激光焊熔池动态行为的作用机理研究
Study on the Influence of Active Flux on the Dynamic Behavior of Molten Pool During Laser Welding
2023年53卷第9期页码：108-115
DOI： 10.7512/j.issn.1001-2303.2023.09.14

扫描看全文

佘昆，李冬辉，元育学，等.活性剂对激光焊熔池动态行为的作用机理研究［J］.电焊机，2023，53（9）：108-115.

SHE Kun, LI Donghui, YUAN Yuxue, et al.Study on the Influence of Active Flux on the Dynamic Behavior of Molten Pool During Laser Welding[J].Electric Welding Machine, 2023, 53(9): 108-115.
佘昆，李冬辉，元育学，等.活性剂对激光焊熔池动态行为的作用机理研究［J］.电焊机，2023，53（9）：108-115. DOI： 10.7512/j.issn.1001-2303.2023.09.14.

SHE Kun, LI Donghui, YUAN Yuxue, et al.Study on the Influence of Active Flux on the Dynamic Behavior of Molten Pool During Laser Welding[J].Electric Welding Machine, 2023, 53(9): 108-115. DOI： 10.7512/j.issn.1001-2303.2023.09.14.

摘要

为阐明活性剂对铝合金激光焊熔池作用机理，建立了三维瞬态移动热源作用下的激光焊接熔池数学模型，研究表面张力梯度及激光吸收率对温度场以及流场的影响规律，揭示活性剂作用下激光焊熔深的增强机制。结果表明，在无活性剂时模拟得到的焊缝形貌与实际试验结果吻合。在低功率铝合金活性激光焊接中，活性剂的加入虽然可以改变表面张力梯度，但表面张力梯度的改变对熔深增加效果不明显。分析认为，活性剂的加入使铝合金对激光吸收率的提高才是熔深增加的主要原因。

Abstract

In order to clarify the action mechanism of active flux on the molten pool during laser welding of aluminum alloys, a mathematical model of the molten pool with a three-dimensional transient moving heat source was established. The influence of surface tension gradient and laser absorptivity on the temperature field and flow field was studied, so as to reveal the enhancement mechanism of penetration depth under the action of active flux. The results showed that the simulated weld morphology was consistent with the actual test results without active flux. In low-power active laser welding of aluminum alloys, although the addition of active flux changed the surface tension gradient, the change of surface tension gradient had no obvious effect on the increase of penetration depth. The analysis showed that the main reason for the increase of penetration depth was the increase of laser absorption rate with the addition of active flux.

关键词

活性剂激光焊铝合金熔池动态行为作用机理

Keywords

active fluxlaser weldingaluminum alloysdynamic behavior of molten poolinfluence mechanism

references

Huang Y， Yuan Y， Yang L， et al. Real-time monitoring and control of porosity defects during arc welding of aluminum alloys［J］. Journal of Materials Processing Technology， 2020， 286： 116832.

Huang Y， Xu S， Yang L， et al. Defect detection during laser welding using electrical signals and high-speed photography［J］. Journal of Materials Processing Technology， 2019， 271： 394-403.

杨文东，杜预，王佳乐，等. 脉冲激光焊接铝/钢异种金属的研究进展［J］. 电焊机， 2023，53（7）：73-80.

YANG W D， DU Y， WANG J L， et al. Research Progress in Pulsed Laser Welding of Aluminum/Steel Dissimilar Metals［J］. Electric Welding Machine， 2023，53（7）：73-80.

Tathgir S， Bhattacharya A， Bera T K. Influence of Current and Shielding Gas in TiO2 Flux Activated TIG Welding on Different Graded Steels ［J］. Materials and Manufacturing Processes， 2015， 30（9）： 1115-1123.

Ahmadi E， Ebrahimi A R. Welding of 316L Austenitic Stainless Steel with Activated Tungsten Inert Gas Process ［J］. Journal of Materials Engineering and Performance， 2015， 24（2）： 1065-1071.

Tseng K H， Chen K L. Comparisons Between TiO2 and SiO2-Flux Assisted TIG Welding Processes［J］. Journal of Nanoscience and Nanotechnology， 2012， 12（8）： 6359-6367.

Sharma P， Dwivedi D K. A-TIG welding of dissimilar P92 steel and 304H austenitic stainless steel： Mechanisms， microstructure and mechanical properties［J］. Journal of Manufacturing Processes， 2019， 44： 166-178.

Parshin S G， Parshin S S， Burkner G， et al. Effect of ultrafine particles of activating fluxes on the laser welding process［J］. Welding International， 2011， 25（7）： 545-549.

Kulkarni A， Dwivedi D K， Vasudevan M. Study of mechanism， microstructure and mechanical properties of activated flux TIG welded P91 Steel-P22 steel dissimilar metal joint［J］. Materials Science and Engineering a-Structural Materials Properties Microstructure and Processing， 2018， 731： 309-323.

Vidyarthy R S， Dwivedi D K. Activating flux tungsten inert gas welding for enhanced weld penetration［J］. Journal of Manufacturing Processes， 2016， 22： 211-228.

Zhao C X， Kwakernaak C， Pan Y， et al. The effect of oxygen on transitional Marangoni flow in laser spot welding［J］. Acta Materialia， 2010， 58（19）： 6345-6357.

Dong W C， Lu S P， Li D Z， et al. GTAW liquid pool convections and the weld shape variations under helium gas shielding［J］. International Journal of Heat and Mass Transfer， 2011， 54（7-8）： 1420-1431.

Gan Z T， Yu G， He X L， et al. Surface-active element transport and its effect on liquid metal flow in laser-assisted additive manufacturing［J］. International Communications in Heat and Mass Transfer， 2017， 86： 206-214.

Yousefi E， Sun Y Q， Kunwar A， et al. Surface tension of aluminum-oxygen system： A molecular dynamics study［J］. Acta Materialia， 2021， 221：117430.

Huang Y， Yuan Y， Feng Y， et al. Effect of activating flux Cr2O3 on microstructure and properties of laser welded 5083 aluminum alloys［J］. Optics & laser technology， 2022， 150： 107930.

庞盛永. 激光深熔焊接瞬态小孔和运动熔池行为及相关机理研究［D］. 湖北：华中科技大学，2011．

PANG S Y. A Study on the Transient Keyhole and Moving Weld Pool Behaviors and Mechanisms of Deep Penetration Laser Welding［D］. Hubei：Huazhong University of Science and Technology，2011.

编辑部网址：http：//www.71dhj.comhttp://www.71dhj.com

文章被引用时，请邮件提醒。

提交

TC4钛合金激光焊接技术研究进展

超大离焦量对TRIP800高强钢激光焊接接头微观组织与力学性能的影响

H62黄铜与T2紫铜搭接激光焊接工艺和焊缝微观组织研究

稀土钇元素对铝合金激光焊接接头组织性能的影响

SiO₂在粉末熔池耦合活性TIG焊熔池表面的过渡行为