基于SYSWELD铝合金搅拌摩擦焊数值模拟及试验
SYSWELD Numerical Simulation and Experimental Study on Friction Stir Welded Aluminum Alloy
- 2022年52卷第7期 页码:1-6
DOI: 10.7512/j.issn.1001-2303.2022.07.01
扫 描 看 全 文
扫 描 看 全 文
王远见,刘坤,许楠,等.基于SYSWELD铝合金搅拌摩擦焊数值模拟及试验[J].电焊机,2022,52(7):1-6.
WANG Yuanjian, LIU Kun, XU Nan, et al.SYSWELD Numerical Simulation and Experimental Study on Friction Stir Welded Aluminum Alloy[J].Electric Welding Machine, 2022, 52(7): 1-6.
在实际工业生产中,通过焊接试验的方法来获得焊缝组织和力学性能的成本较高,因此数值模拟成为预测焊缝微观组织和力学性能的主要方法。基于SYSWELD软件建立了6061-T6铝合金搅拌摩擦焊缝温度场和材料流动的模型,采用电子背散射衍射技术对焊缝区进行微观组织表征。结果表明:随着搅拌头转速的升高,焊接峰值温度和材料流速逐渐增大。焊缝横截面方向温度呈M形不对称分布,且前进侧比后退侧温度高。焊缝中心的晶粒尺寸随着转速的增加而增大、小角度晶粒比例增加且剪切织构强度增强;相同搅拌头转速下前进侧晶粒尺寸和小角度晶粒的比例比后退侧大。焊缝微观组织表征结果与温度场和材料流动的模拟结果基本吻合。
In actual industrial production, the cost of obtaining weld microstructure and mechanical properties by welding test is high, so numerical simulation has become the main method to predict weld microstructure and mechanical properties.The temperature field and the material flow of friction stir welded 6061-T6 aluminum alloy are established based on SYSWELD software. The microstructure of the weld is characterized by electron backscatter diffraction. The results showed that the peak temperature and material flow rate increased with the increase of the rotation rate. The cross-section of the weld showed an asymmetrical M-shaped temperature distribution, and the temperature on the advancing side was higher than that of the retreating side. Due to the increased rotation rate, the grain size, the ratio of low-angle grain boundaries, and the shear texture intensity increased. At the same rotation rate, the grain size and the ratio of low-angle grain boundaries on the advancing side are larger than those of the retreating side. The microstructure characterization results of the weld are consistent with the simulation results of temperature and material flow.
铝合金搅拌摩擦焊温度材料流动微观组织
aluminum alloyfriction stir weldingtemperaturematerials flowmicrostructure
刘琪. 搅拌摩擦表面处理数值模拟[D]. 湖北:湖北工业大学, 2016.
LIU Qi. Numerical simulation of friction stir processing[D]. Hubei:Hubei University of Technology,2016.
Thomas W M, Needlham J C, Dawes C J, et al. Friction stir butt welding[P]. Internation patent application number PCT/GB92/02203 and GB patent application 9125978.8, 1991-12-06.
万胜强, 吴运新, 龚海, 等. 2219铝合金搅拌摩擦焊温度与残余应力热力耦合模拟[J]. 热加工工艺, 2019,48(13):159-163.
WAN Shengqiang,WU Yunxin,GONG Hai,et al. Thermal Mechanical Coupling Simulation of Temperature and Residual Stress in Friction Stir Welding of 2219 Aluminum Alloy[J]. Hot Working Technology, 2019,48(13):159-163.
刘其鹏,顾乃建,刘泽,等. AA6061-T6板材搅拌摩擦焊温度场仿真[J].大连交通大学学报,2018,39(3):80-85.
LIU Qipeng,GU Naijian,LIU Ze,et al. Simulation of Temperature Field of AA6061-T6 Sheet in Friction Stir Welding[J]. Journal of Dalian Jiaotong University, 2018, 39(3): 80-85.
周文静, 杜柏松, 卢小明. 铝合金搅拌摩擦焊温度场数值模拟及参数影响分析[J]. 热加工工艺, 2021, 50(7):156-160.
ZHOU Wenjing,DU Baisong,LU Xiaoming. Numerical Simulation of Temperature Field and Parameter Influence Analysis of Friction Stir Welding of Aluminum Alloy[J].Hot Working Technology,2021,50(7):156-160.
崔超, 吴志生, 柴斐, 等. 5A06铝合金搅拌摩擦焊温度场数值模拟[J]. 焊接技术, 2017, 46(3):12-15.
CUI Chao,WU Zhisheng,CAI Wen,et al. Numerical simulation of temperature field during friction stir welding for 5A06 aluminum alloy[J]. Welding Technology, 2017, 46(3):12-15.
张骁, 王敏, 张会杰. 2A14铝合金双轴肩搅拌摩擦焊的温度场模拟及测定[J]. 焊接学报, 2015(9): 16-19.
ZHANG Xiao,WANG Min,ZHANG Huijie. Simulation and test of bobbin tool friction stir welding temperature field of 2A14 aluminum alloy[J]. Welding & Joining, 2015(9): 16-19.
邓清洪, 蔡华文, 丁常青, 等. 42 mm厚的6082-T6铝合金双面搅拌摩擦焊工艺研究[J]. 焊接技术, 2019,48(11): 58-60.
DENG Qinghong,CAI Huawen,DING Changqing,et al. Research on double-side friction stir welding process of 42 mm thick 6082-T6 aluminum alloy[J]. Welding Technology, 2019,48(11): 58-60.
王瑫. 搅拌摩擦焊工艺参数对6061-T6时效硬化铝合金显微组织及性能的影响[D]. 山东:山东大学, 2018.
WANG Tao. Effect of friction stir welding parameters on microstructure and properties of 6061-T6 ageing hardenable aluminum alloy[D]. Shandong:Shandong University, 2018.
肖毅华, 张浩锋. 6061-T6铝合金搅拌摩擦焊温度场的数值模型和参数影响分析[J]. 机械科学与技术, 2017(1): 75-79.
XIAO Yihua,ZHANG Haofeng. Numerical Model and Influence Analysis of Parameters for Temperature Field in Friction Stir Welding of 6061-T6 Aluminum Alloy[J]. Mechanical Science and Technology for Aerospace Engineering, 2017(1): 75-79.
相关作者
相关机构