脉冲宽度对亚微米级TC4钛合金激光微接焊缝成形及力学性能的影响
Influence of Pulse Width on Laser Micro-weld Formation and Mechanical Properties of Sub-micron TC4 Titanium Alloy
- 2022年52卷第6期 页码:126-130
DOI: 10.7512/j.issn.1001-2303.2022.06.16
扫 描 看 全 文
扫 描 看 全 文
居琪萍,汪立高,许明方,等.脉冲宽度对亚微米级TC4钛合金激光微接焊缝成形及力学性能的影响[J].电焊机,2022,52(6):126-130.
JU Qiping, WANG Ligao, XU Mingfang, et al.Influence of Pulse Width on Laser Micro-weld Formation and Mechanical Properties of Sub-micron TC4 Titanium Alloy[J].Electric Welding Machine, 2022, 52(6): 126-130.
采用脉冲激光焊对0.2 mm厚TC4钛合金薄板进行对接焊,研究脉冲宽度对焊缝成形、微观组织和接头强度的影响。结果表明,由于冷却速度较快,得到的焊缝微观组织均为取向随机的针状α'马氏体相组成的网篮组织。随着脉冲宽度的增加,焊缝形貌由半圆形向X形转变。当脉冲宽度在2.7~4.9 ms时,试样的抗拉强度呈逐步递增趋势,脉冲宽度为4.9 ms时抗拉强度达到最大值(898.58 MPa)。硬度测试结果表明,脉冲宽度的增加导致焊接线能量增加,当脉冲宽度为4.9 ms时,焊缝区显微硬度达到最大值(379 HV)。
TC4 titanium alloy has attracted extensive attention in various fields because of its excellent weldability. The butt welding of 0.2 mm TC4 titanium alloy sheet was carried out by pulse laser welding. The effects of pulse width on weld formation, microstructure and joint strength were studied. The results show that the microstructure of the weld is composed of needle martensite α' phase with random orientation due to the high cooling rate. With the increase of pulse width, the joint morphology changes from semicircle to X shape. When the pulse width is between 2.7 ms and 4.9 ms, the tensile strength of the sample increases gradually, and reaches the maximum value (898.58 MPa) when the pulse width is 4.9 ms. The hardness test results show that the increase of pulse width leads to the increase of welding line energy. When the pulse width is 4.5 ms, the microhardness of weld zone reaches the maximum value (379 HV).
超薄钛合金脉冲激光焊微观组织力学性能
ultra-thin titanium alloypulse laser weldingmicrostructuremechanical properties
许明方, 陈玉华, 陈伟, 等. Ti-6Al-4V组织相变研究进展[J].精密成形工程, 2020, 12(02): 93-97.
XU Mingfang, CHEN Yuhua, CHEN Wei, et al. Research Progress of Ti-6Al-4V Phase Transition[J]. Journal of Netshape Forming Engineering, 2020, 12(02): 93-97.
张建斌, 余冬梅. 钛及钛合金的激光表面处理研究进展[J].稀有金属材料与工程,2015,44(01):247-254.
ZHANG Jianbin, YU Dongmei. Research Progress on Laser Surface Treatment of Titanium and Titanium Alloys[J]. Rare Metal Materials and Engineering, 2015,44(01): 247-254.
房卫萍, 黎小辉, 张宇鹏, 等. 热处理对100 mm厚TC4钛合金电子束焊接接头性能的影响[J]. 电焊机,2017, 47(06): 82-87.
FANG Weiping, LI Xiaohui, ZHANG Yupeng, et al. Effect of heat treatment on mechanical properties of welded joint of electron beam welding for TC4 titanium alloy with 100 mm thickness[J]. ElectricWelding Machine, 2017, 47(06): 82-87.
刘兰胜. TiNi合金/不锈钢异种材料微激光焊缝组织性能[J]. 电焊机, 2015, 45(03): 122-126.
LIU Lansheng. Study on the TiNi alloy/stainless steel micro laser weld dissimilar materials organization performance[J]. ElectricWelding Machine,2015, 45(03):122-126.
陈玉华, 孙松伟, 周兴汶, 等. 脉冲宽度对超薄TiNi/不锈钢激光焊接头TiNi侧界面的影响[J].稀有金属材料与工程, 2019, 48(06): 1916-1920.
CHEN Yuhua, SUN Songwei, ZHOU Xingwen, et al. Effect of Pulse Width on TiNi Side Interface of Laser Welded Joint of TiNi/Stainless Steel[J]. Rare Metal Materials and Engineering, 2019, 48(06): 1916-1920.
环鹏程,王晓南,朱天才,等.800 MPa级热轧高强钢激光焊接接头的组织和力学性能[J].中国激光,2019,46(01):91-99.
HUAN Pengcheng, WANG Xiaonan, ZHU Tiancai, et al. Microstructure and Mechanical Properties of Laser Welded Joint of 800 MPa Grade Hot-Rolled High Strenth Steel[J].Chinese Journal of Lasers,2019,46(01):91-99.
许赛,杨立军,徐书峰,等.激光深熔焊等离子体电信号振荡特征与焊缝熔深的特征关系[J].中国激光,2020,47(01):113-121.
XU Sai, YANG Lijun, XU Shufeng, et al. Relation between Plasma Electrical Signal Oscillation and Weld Depth in Laser Deep Penetration Welding[J]. Chinese Journal of Lasers, 2020,47(01):113-121.
张建, 杨锐. 激光焊接钛合金薄板时的功率控制[J]. 中国激光, 2012, 39(1): 1-4.
ZHANG Jian, YANG Rui. Control of Laser Power During Titanium Alloy Thin Plate Welding[J]. Chinese Journal of Lasers, 2012, 39(1): 1-4.
陈玉华, 柯黎明, 徐世龙. TiNi形状记忆合金薄片的微激光焊接工艺研究[J]. 热加工工艺, 2009, 38(9): 91-93.
CHEN Yuhua, KE Liming, XU Shilong. Study on Micro-laser Welding Process of TiNi Shape Memory Alloy Sheet[J]. Hot Working Technology, 2009, 38(9): 91-93.
虞鸿江, 范如意, 黄坚, 等. TC11高强钛合金激光焊接接头的显微组织与力学性能[J]. 中国有色金属学报, 2015, 25(1): 1-8.
YU Hongjiang, FAN Ruyi, HUANG Jian, et al. Microstructure and mechanical properties of high-strength TC11 titanium alloy joints welded by laser beam[J]. The Chinese Journal of Nonferrous Metals, 2015, 25(1): 1-8.
LEI Z L, DONG Z J, CHEN Y B, HUANG L, ZHU R C. Microstructure and Mechanical Properties of Laser Welded Ti-22Al-27Nb/TC4 Dissimilar Alloys[J]. Materials Science and Engineering A, 2013, 559: 909-916.
GONG WH, CHEN YH, KE LM. Microstructure and Properties of Laser Micro Welded Joint of TiNi Shape Memory Alloy[J]. Science Direct, 2011, 21: 2044-2048.
相关作者
相关机构