转向架用S355J2W钢MAG焊接接头残余应力研究

果伟; 张志毅; 邱培现; 马传平

高速列车金属材料及焊接先进技术 | 浏览量 : 59 下载量: 74 CSCD: 2

导出
分享给微信好友或者朋友圈

分享
收藏
专辑

转向架用S355J2W钢MAG焊接接头残余应力研究
Research on the residual stress of S355J2W steel MAG welded joints of bogies
- 角色： First author 第一作者
- 机构：
  中车青岛四方机车车辆股份有限公司
果伟
1 ，
- 机构：
  中车青岛四方机车车辆股份有限公司
张志毅
1 ，
- 机构：
  中车青岛四方机车车辆股份有限公司
邱培现
1 ，
- 机构：
  西南交通大学材料科学与工程学院
马传平
2
2018年48卷第3期页码：300-303
DOI：

扫描看全文

引用
果伟, 张志毅, 邱培现, 等. 转向架用S355J2W钢MAG焊接接头残余应力研究[J]. 电焊机, 2018,48(3):300-303.

GUO Wei, ZHANG Zhiyi, QIU Peixian, et al. Research on the residual stress of S355J2W steel MAG welded joints of bogies[J]. 2018,48(3):300-303.
果伟, 张志毅, 邱培现, 等. 转向架用S355J2W钢MAG焊接接头残余应力研究[J]. 电焊机, 2018,48(3):300-303. DOI：

GUO Wei, ZHANG Zhiyi, QIU Peixian, et al. Research on the residual stress of S355J2W steel MAG welded joints of bogies[J]. 2018,48(3):300-303. DOI：

摘要

利用X射线衍射法和超声临界折射纵波法测量和分析S355J2W钢MAG焊接接头的起弧区、中心区和收弧区残余应力。结果表明:超声波法和X射线衍射法均可用于S355J2W钢MAG焊接接头的残余应力测量,在焊缝和热影响区,超声波法的应力测量值比X射线法的大30⁴0 MPa。各测试区残余应力分布趋势相近,在焊缝及近缝热影响区为数值较大的残余拉应力,远离焊缝中心的母材为压应力。中心区的残余应力峰值大于起弧区和收弧区。

译

Abstract

The residual stress of the S355 J2 W steel MAG welded joint was measured and analyzed by X-ray diffraction method and ultrasonic critical refraction longitudinal wave method. The results show that:the X-ray diffraction method and ultrasonic critical refraction longitudinal wave method can be used for S355 J2 W steel MAG welded joint residual stress measurement. The residual stress value of the ultrasonic method is 30 ⁴0 MPa larger than that of the X-ray method in the weld and heat affected zone. The distribution of residual stress in each test area is similar,and the residual tensile stress is larger in the weld and heat affected zone,and the base metal which is away from the center of the weld is residual compressive stress. The residual stress peak of the central area of is greater than the starting arc region and the ending arc region.

译

关键词

S355J2W钢; MAG焊接接头; 残余应力

译

Keywords

S355J2W steel; MAG welded joints; residual stress

译

摘要

利用X射线衍射法和超声临界折射纵波法测量和分析S355J2W钢MAG焊接接头的起弧区、中心区和收弧区残余应力。结果表明:超声波法和X射线衍射法均可用于S355J2W钢MAG焊接接头的残余应力测量,在焊缝和热影响区,超声波法的应力测量值比X射线法的大30,4,0 MPa。各测试区残余应力分布趋势相近,在焊缝及近缝热影响区为数值较大的残余拉应力,远离焊缝中心的母材为压应力。中心区的残余应力峰值大于起弧区和收弧区。

Abstract

The residual stress of the S355 J2 W steel MAG welded joint was measured and analyzed by X-ray diffraction method and ultrasonic critical refraction longitudinal wave method. The results show that:the X-ray diffraction method and ultrasonic critical refraction longitudinal wave method can be used for S355 J2 W steel MAG welded joint residual stress measurement. The residual stress value of the ultrasonic method is 30 ,4,0 MPa larger than that of the X-ray method in the weld and heat affected zone. The distribution of residual stress in each test area is similar,and the residual tensile stress is larger in the weld and heat affected zone,and the base metal which is away from the center of the weld is residual compressive stress. The residual stress peak of the central area of is greater than the starting arc region and the ending arc region.