奥氏体耐热钢SA-213TP310HCbN采用ERNiCr-3焊接接头性能试验及应用研究

张玮; 莫春鸿

焊接工艺 | 浏览量 : 0 下载量: 85 CSCD: 0

PDF
导出
分享
收藏
专辑

奥氏体耐热钢SA-213TP310HCbN采用ERNiCr-3焊接接头性能试验及应用研究
Performance test and application of welded joint of welding austenitic heat-resistant steel SA-213TP310HCbN with ERNiCr-3
2019年49卷第8期页码：72-75
DOI：

扫描看全文

张玮, 莫春鸿. 奥氏体耐热钢SA-213TP310HCbN采用ERNiCr-3焊接接头性能试验及应用研究[J]. 电焊机, 2019,49(8):72-75.

ZHANG Wei, MO Chunhong. Performance test and application of welded joint of welding austenitic heat-resistant steel SA-213TP310HCbN with ERNiCr-3[J]. 2019,49(8):72-75.
张玮, 莫春鸿. 奥氏体耐热钢SA-213TP310HCbN采用ERNiCr-3焊接接头性能试验及应用研究[J]. 电焊机, 2019,49(8):72-75. DOI：

ZHANG Wei, MO Chunhong. Performance test and application of welded joint of welding austenitic heat-resistant steel SA-213TP310HCbN with ERNiCr-3[J]. 2019,49(8):72-75. DOI：

摘要

通过对比分析奥氏体耐热钢SA-213TP310HCbN现有可选焊接材料,认为ERNiCr-3是焊接SA-213TP310HCbN的优选方案,对采用ERNiCr-3焊接的SA-213TP310HCbN接头性能进行了试验,并分析研究其应用性。结果表明,采用ERNiCr-3焊接的SA-213TP310HCbN接头常温性能满足焊接工艺评定和试件检验标准的要求,接头高温短时拉伸性能能够达到母材的要求,能够满足工程应用的要求。可对焊丝ERNiCr-3焊缝金属室温抗拉强度进行规定作为内控标准,以更好地保证接头性能。

Abstract

By comparing and analyzing the available welding materials for austenitic heat-resistant steel SA-213TP310HCbN,it is considered that ERNi Cr-3 is the best choice for welding SA-213TP310HCbN. The performance of welded joints obtained by welding SA-213TP310HCbN with ERNi Cr-3 is tested,and the application of these welded joints is analyzed. It is considered that the room temperature properties of welded joints of welding SA-213TP310HCbN with ERNi Cr-3 can meet the requirements of welding procedure qualification and test specimen inspection standards,and the short-term tensile properties of welded joints at a high temperature can meet the requirements of base metal and engineering applications.

关键词

SA-213TP310HCbN焊接材料接头性能应用

Keywords

SA-213TP310HCbNwelding materialjoint propertiesapplication

references

文章被引用时，请邮件提醒。

提交

铝锂合金的搅拌摩擦焊及其改型工艺研究进展

奥氏体不锈钢高速带极电渣堆焊用烧结焊剂CHF25B的研制