Effect of Rolling and Drawing on the Structure and Properties of Inconel 625 Wires

MA Jiguo; WANG Xiaojun; MIAO Chengpeng; DONG Shengmao; ZHANG Zhen; CHEN Long

doi:10.7512/j.issn.1001-2303.2024.06.10

Welding Material | Views : 0 下载量: 12 CSCD: 0

PDF
Export
Share
Collection
Album

Effect of Rolling and Drawing on the Structure and Properties of Inconel 625 Wires
Vol. 54, Issue 6, Pages: 60-65(2024)
Published： 25 June 2024 ，
DOI： 10.7512/j.issn.1001-2303.2024.06.10
稿件说明：

移动端阅览

马继国，王晓军，苗承鹏，等.轧制拉拔对Inconel 625线材组织结构及性能的影响［J］.电焊机，2024，54（6）：60-65.

MA Jiguo, WANG Xiaojun, MIAO Chengpeng, et al.Effect of Rolling and Drawing on the Structure and Properties of Inconel 625 Wires[J].Electric Welding Machine, 2024, 54(6): 60-65.
马继国，王晓军，苗承鹏，等.轧制拉拔对Inconel 625线材组织结构及性能的影响［J］.电焊机，2024，54（6）：60-65. DOI： 10.7512/j.issn.1001-2303.2024.06.10.

MA Jiguo, WANG Xiaojun, MIAO Chengpeng, et al.Effect of Rolling and Drawing on the Structure and Properties of Inconel 625 Wires[J].Electric Welding Machine, 2024, 54(6): 60-65. DOI： 10.7512/j.issn.1001-2303.2024.06.10.

摘要

为明确自主研发Inconel 625焊丝的优势与不足，并为优化焊丝生产工艺提供科学依据。应用SEM、XRD、室温拉伸试验和显微硬度测试等方法，分析了Inconel 625焊丝在轧制拉拔工艺后的微观组织和力学性能。结果发现，Inconel 625合金为单一的奥氏体相；变形织构使得轧制和冷拔线坯个别衍射峰强度明显升高。不同线坯的横截面金相组织为等轴晶，热轧和冷拔线坯含形变孪晶，拉拔软态线坯存在大量退火孪晶。热轧态Inconel 625线坯经固溶处理显微硬度为219.33 HV0.5；固溶处理温度和时间控制不准确会使线坯局部出现晶粒异常长大；冷拔硬态线坯硬度值受加工硬化影响增大至522.32 HV0.5，延伸率降低至4.37%。退火处理消除了合金内应力和加工硬化，使得拉拔软态线坯的最小平均晶粒尺寸从硬态的2.66 μm增长至9.5 μm，延伸率达到65.13%，抗拉强度为418.92 MPa。试验结果证明，自主研发的Inconel 625焊丝的各项指标均达到国内外标准要求，说明通过精确控制加工和热处理工艺，可以有效提升焊丝的性能。

Abstract

SEM

XRD

room temperature tensile test

microhardness and other methods are used to analyze the microstructure and mechanical properties of Inconel 625 wire after rolling and drawing processandfinished wires at home and abroad

and clarify the advantages and shortcomings

so as to optimize the production process of the wire. The results show that the structure of Inconel625 alloy is a single austenite phase by XRD. After rolling and cold drawing

some diffraction peak intensity of wire become significantly higher than others because of deformation texture.Cross section microstructure of the different wires is equiaxed grains

deformation twins may be found in hot rolled and cold drawn wire

and a large number of annealed twins may be also observed in the soft state of drawn wire.Microhardness is 219.33 HV0.5 for solution state of rolling Inconel 625. Local grain abnormality growth may be observed if solution treatment temperature and time is inaccurate. Microhardness increased to 522.32 HV0.5 for Cold-drawn state of Inconel 625 because of work-hardening

while elongation reduced to 4.37%. The annealing treatment eliminated the internal stresses and work hardening of the cold draw alloy

so that the minimum average grain size grows to 9.5 μm from 2.66 μm.Elongation of 65.13%

and tensile strength of 418.92 MPa may be gained for soft drawn wire. All the indexes of the finished wires meet the requirements of domestic and foreign standards.

关键词

Inconel625焊丝微观组织力学性能孪晶

Keywords

Inconel625 wiremicrostructuremechanical propertiestwins

references

Cortial F，Corrieu J M，Vernot-Loier C.Heat treatments of weld alloy 625： Influence on the microstructure， mechanical properties and corrosion resistance［J］. Metallurgical and Materials Transactions A-Physical Metallurgy And Materials Science，1995，26（05）：859-870.

Alexandrov B T，Hope M A T，Jeffrey W. Weldability studies of high-Cr，Ni-base filler metals for power generationapplications［J］. Welding in the World，2011，55（3-4）：65-76.

倪莉，张军，王博，等. 镍基高温合金设计的研究进展［J］. 材料导报，2014，28（03）：1-6+16.

NI L，ZHANGJ，WANGB，et al. Research progress in the design of nickel-based superalloys［J］. Materials Reports，2014，28（03）：1-6+16.

Tehovnik F，Burja J，Podgornik B，et al. Microstructural evolution of Inconel 625 during hot rolling［J］. Materiali in Tehnologije，2015，49（5）：801-806.

GB/T 15620-2008.镍及镍合金焊丝［S］.北京：中国标准出版社，2008：5+14.

AWS 5.14-2018.Specification for Nickel and Nickel-Alloy Bare Welding Electrodes and Rods［S］.American National Standards Institute，2018：5.

GB/T 6394-2017. 金属平均晶粒度测定方法［S］. 北京：中国标准出版社，2017：7-12.

袁珊珊，刘海定，王小岩，等. 国产ERNiCrMo-3镍基合金焊丝热加工成型技术研究［J］. 电焊机，2021，51（12）：111-115.

YUAN S S，LIU H D，WANGXY，et al.Domestic ERNiCrMo-3 nickel-based alloy wire hot workingandforming technology research［J］. Electric Welding Machine，2021，51（12）：111-115.

高钰璧，丁雨田，孟斌，等. Inconel625合金中析出相演变研究进展［J］. 材料工程，2020，48（05）：13-22.

GAOY B，DINGYT，MENGB，et al.Progress in the study of precipitated phase evolution in Inconel 625 alloy［J］. Journal of Materials Engineering，2020，48（05）：13-22.

崔约贤，王长利编著.金属断口分析［M］.黑龙江：哈尔滨工业大学出版社，1998.27-30.

Alert me when the article has been cited

提交

Study on Process Optimization and Microstructure and Properties of A105 Laser Welding

Microstructure and Shear Strength of Diamond/Cu Alloy Joint Brazed with Ag-Cu-Sn-Cr Filler Metal

Study of Microstructure, Mechanical Properties, and Creep Properties of GH4169 Alloy After Homogenization Heat Treatment Using Arc Additive Manufacturing

Microstructure and Mechanical Properties of Friction Plug Repair Welding Joint on Low Alloy High Strength Steel Threaded Hole

Resistance Spot Welding Technology of High Strength Steel