激光-KTIG复合焊接工艺下的匙孔行为研究与工艺特点
Study of Keyhole Behavior and Process Characteristics in Laser-KTIG Hybrid Welding
- 2026年56卷第9期 页码:1-9
收稿:2026-07-20,
修回:2026-09-07,
纸质出版:2026-09-20
DOI: 10.7512/j.issn.1001-2303.2026.09.01
移动端阅览

浏览全部资源
扫码关注微信
收稿:2026-07-20,
修回:2026-09-07,
纸质出版:2026-09-20
移动端阅览
为了扩大KTIG的焊接工艺窗口和电弧稳定性,采用激光-KTIG复合焊接方法对对碳钢(Q235)与不锈钢(304L)进行焊接试验。研究了激光照射位置、焊接速度及激光功率对复合焊接过程稳定性和焊缝成形的影响,并借助X射线透射成像原位观测装置,实时采集了复合焊接与单独KTIG焊接过程中匙孔的生成与演化图像。结果表明,激光照射于匙孔前壁时形成电弧穿孔模式,照射于匙孔后壁时形成激光穿孔模式。在电弧穿孔模式下,焊接稳定性与电弧形态主要受到焊接速度与激光功率的影响。在匙孔产生与演化方面,激光的照射改变了电弧的燃弧位置与挺直性,致使电弧匙孔发生偏移,偏移量的多少取决于焊接速度和激光功率,通过合理的设置参数,可将匙孔优化为竖直状态,竖直状态下的匙孔降低了工艺气孔的倾向。
To broaden the process window and improve arc stability of KTIG welding
laser‑KTIG hybrid welding was employed to carry out butt‑welding experiments on Q235 carbon steel and 304L stainless steel. The influences of laser irradiation position
welding speed and laser power on process stability and weld formation of hybrid welding were investigated. An in‑situ X‑ray transmission imaging system was utilized to acquire real‑time images of keyhole initiation and evolution during hybrid welding and single KTIG welding. The results reveal that the arc‑penetration mode is generated when the laser irradiates the front wall of the keyhole
while the laser‑penetration mode forms as the laser irradiates the rear wall of the keyhole. Under the arc‑penetration mode
welding stability and arc morphology are predominantly governed by welding speed and laser power. For keyhole generation and evolution
laser irradiation modifies the arc ignition position and arc stiffness
resulting in keyhole deflection whose magnitude depends on welding speed and laser power. Appropriate parameter configuration can achieve a vertical keyhole geometry
which mitigates the susceptibility to process‑related porosity.
Gao M , Zeng X , Hu Q . Effects of gas shielding parameters on weld penetration of CO 2 laser-TIG hybrid welding [J]. J Mater Process Technology , 2007 , 184 ( 1-3 ): 177 - 183 .
Han L , Han T , Wang B , et al . Effects of Keyhole Tungsten Inert Gas Welding Parameters on 2205 Duplex Stainless Steel Welded Joints [J], J. of Materi Eng and Perform , 2022 , 31 : 1358 - 1372 .
Liu L , Chen M . Interactions between laser and arc plasma during laser-arc hybrid welding of magnesium alloy [J]. Opt. Lasers Eng. , 2011 , 49 ( 9-10 ): 1224 - 1231 .
Casalino G , Mortello M , Leo P , et al . Study on arc and laser powers in the hybrid welding of AA5754 Al-alloy [J]. Mater. Des. , 2014 , 61 : 191 - 198 .
Zhang L J , Ning J , Zhang X J , et al . Single pass hybrid laser-MIG welding of 4 mm thick copper without preheating [J]. Mater. Des. , 2015 , 74 : 1 - 18 .
Fan X Q , Tristan G F , Samuel J C , et al . Magnetic modulation of keyhole instability during laser welding and additive manufacturing [J]. Science , 2025 , 387 ( 6736 ): 864 - 869 .
Lathabai S , Jarvis B L , Barton K J . Comparison of keyhole and conventional gas tungstenarc welds in commercially pure titanium [J]. Materials Science & Engineering A , 2001 , 299 ( 1-2 ): 81 - 93 .
Lv X Z , Liu L M . Characteristics of laser-offset-TIG hybrid welding of AZ31Mg alloy with 6061Al alloy via Zn filler [J]. Optics & Laser Technology , 2022 , 152 : 108126 .
Turichin G , Kuznetsov M , Tsibulskiy I , et al . Hybrid laser-arc welding of the high-strength shipbuilding steels:equipment and technology [J]. Phys Procedia , 2017 , 89 : 156 - 163 .
Swanson P T , Page C J , Read E , et al . Plasma augmented laser welding of 6 mm steel plate [J]. Science and Technology of Welding and Joining , 2007 , 12 ( 2 ): 153 - 160 .
Campana G , Ascari A , Fortunato A , et al . Hybrid laser-MIG welding of aluminum alloys:The influence of shielding gases [J]. Appl Surf Sci , 2009 , 255 : 5588 - 5590 .
Vaidya W V , Angamuthu K , Koçak M , et al . Strength and Fatigue Resistance of Laser-MIG Hybrid Butt Welds of an Airframe Aluminium Alloy AA6013 [J]. Weld World , 2006 , 50 : 88 - 97 .
Ishide T , Shuho Tsubota , Masao Watanabe . Latest MIG,TIG Arc-YAG laser hybrid welding systems for various welding products [J]. Proceedings of SPIE - The International Society for Optical Engineering , 2003 : 4831 .
Webster S , Kristensen J K , Petring D . Joining of thick section steels using hybrid laser welding [J]. Ironmaking & Steelmaking , 2008 , 35 ( 7 ): 496 - 504 .
Ono M , Shinbo Y , Yoshitake A , et al . Development of laser-arc hybrid welding [J]. NKK Technical Review , 2002 ( 86 ): 58922806 .
Zhu Y , Cai Y , Dong H , et al . Tailoring droplet transfer and molten pool flow during hybrid laser arc welding of nickel base alloy [J]. Optics & Laser Technology , 2022 , 147 : 107620 .
Reisgen U , Olschok S , Engels O . Laser beam submerged arc hybrid welding:A novel hybrid welding process [J]. Journal of Laser Applications , 2018 , 30 ( 4 ): 042012 .
Ren Z , Gao L , Clark S J , et al . Machine learning-aided real-time detection of keyhole pore generation in laser powder bed fusion [J]. Science , 2023 , 379 ( 6627 ): 89 - 94 .
Rosellini C , Jarvis L . The keyhole TIG welding process:a valid alternative for valuable metal joints [J], Welding International , 2009 , 23 ( 8 ): 616 - 621 .
Jarvis L . Keyhole gas tungsten arc welding:a new process variant [M]. Wollongong,NSW,Australia : University of Wollongong , 2001 .
Fei Z , Pan Z , Cuiuri D , et al . Microstructural characterization and mechanical properties of K-TIG welded SAF2205/AISI316L dissimilar joint [J]. J. Manuf. Process. , 2019 , 45 ( 9 ): 340 - 355 .
Wang L , Liu Y , Yang C G , et al . Study of porosity suppression in oscillating laser-MIG hybrid welding of AA6082 aluminum alloy [J]. Journal of Materials Processing Technology , 2021 , 292 : 117053 .
相关作者
相关机构
公网安备11010802024621