低合金钢角焊缝剪切性能评价方法研究

纪昂; 陆智俊; 张立平; 彭根琛

doi:10.7512/j.issn.1001-2303.2024.09.14

焊接工艺 | 浏览量 : 0 下载量: 1944 CSCD: 0

PDF
导出
分享
收藏
专辑

低合金钢角焊缝剪切性能评价方法研究
Study on Evaluation Methods for Shear Property of Low Alloy Steel Fillet Weld
2024年54卷第9期页码：105-110
收稿：2024-01-24，

修回：2024-03-05，

纸质出版：2024-09-25
DOI： 10.7512/j.issn.1001-2303.2024.09.14
稿件说明：

移动端阅览

纪昂，陆智俊，张立平，等.低合金钢角焊缝剪切性能评价方法研究［J］.电焊机，2024，54（9）：105-110. DOI： 10.7512/j.issn.1001-2303.2024.09.14.

JI Ang, LU Zhijun, ZHANG Liping, et al.Study on Evaluation Methods for Shear Property of Low Alloy Steel Fillet Weld[J].Electric Welding Machine, 2024, 54(9): 105-110. DOI： 10.7512/j.issn.1001-2303.2024.09.14.

摘要

角焊缝等承载计算方法在角焊缝焊脚尺寸低成本设计方面发挥了重要作用，但同时该方法也对焊丝熔敷金属剪切性能的定量计算提出了新的要求。本文采用搭接接头角焊缝进行低合金钢焊丝熔敷金属剪切性能仿真及试验研究，通过提出新的焊缝抗剪强度计算公式，并基于研究结果给出推荐的剪切性能评价方法。结果表明：角焊缝的剪切开裂角度在22.5°附近，仿真计算获得的不同角度下角焊缝剪切应力变化曲线也证明了该结论。熔深的存在并不会影响开裂角度，但是会起到增大焊脚的作用。焊丝熔敷金属剪切性能评价试验应采用一般尺寸、多道焊形式，从而获得具有代表性的熔敷金属剪切强度。另外推荐采用“求和计算断裂面宽度”的方式来获得剪切强度，虽然剪切强度会降低10%左右，但由于通过直接定义开裂角度为理论角度，断裂面宽度为“焊脚+熔深”，因此可以尽可能地减少测量导致的误差因素，有效增加计算结果的普遍适用性。

Abstract

In recent years

the equal load-carrying calculation method for fillet welds has played a significant role in the low-cost design of fillet weld sizes. At the same time

this method has also posed new requirements for the quantitative calculation of the shear performance of the deposited metal. In this paper

the simulation and experimental study on the shear properties of deposited metal from low alloy steel welding wire are carried out by using the lap joint fillet weld. A new formula for calculating the shear strength of fillet weld is proposed

and a recommended method for evaluating the shear properties is given based on the research results. The results show that the shear cracking angle of fillet weld is around 22.5°

and the existence of penetration does not affect the cracking angle

but equal to the increasing of weld size. The test should adopt the general size

multi-pass welding method

so as to obtain the representative shear strength of the deposited metal. In addition

it is recommended to calculate the sum size of the fracture surface to obtain the shear strength. Although the shear strength will be reduced by about 10%

the influencing factors can be much less and the general applicability of the calculation results can be effectively increased by directly defining the cracking angle as the theoretical angle and the width of the fracture surface as "weld size plus penetration".

关键词

Keywords

references

中国机械工程学会焊接学会 . 焊接手册 . 第3卷，焊接结构［M］. 机械工业出版社， 2015 .

Kuhlmann U ， Hans P G ， Rasche C . High-strength steel fillet welded connections ［J］. Steel Construction ， 2010 ， 1 （ 1 ）： 77 - 84 .

Rafael P ， Jose C . On strength criteria of fillet welds ［J］. International Journal of Mechanical Sciences ， 2009 ， 51 （ 8 ）： 609 - 618 .

Huang T D ， Michael H ， Lee K ， et al . Reduction of overwelding and distortion for naval surface combatants. part 2： weld sizing effects on shear and fatigue performance ［J］. Journal of Ship Production & Design ， 2017 ， 32 （ 1 ）： 21 - 36 .

Kato B ， Morita K . Strength of transverse fillet welded joints ［J］. Welding Journal ， 1974 ， 53 （ 2 ）： 59 - 64 .

Kennedy D L ， Kriviak G J . The strength of fillet welds under longitudinal and transverse shear：a paradox ［J］. Canadian Journal of Civil Engineering ， 1985 ， 12 （ 1 ）： 226 - 231 .

Structual Welding Code—Steel： A WS D1.1-2020 ［S］.

Lu H ， Dong P ， Boppudi S . Strength analysis of fillet welds under longitudinal and transverse shear conditions ［J］. Marine Structures ， 2015 ， 43 （ 10 ）： 87 - 106 .

Lu H ， Dong P . An analytical shear strength model for load-carrying fillet-welded connections incorporating nonlinear effects ［J］. Journal of Structural Engineering ， 2020 ， 146 （ 3 ）： 1 - 11 .

Dong P ， Nie C ， Yang X ， et al . A math-based design for produceability evaluation of titanium applications in ship hull structures ［J］. Transactions - Society of Naval Architects and Marine Engineers ， 2013 ， 120 ： 299 - 305 .

Dong P ， Nie C . A traction stress based shear strength definition for fillet welds ［J］. The Journal of Strain Analysis for Engineering Design ， 2012 ， 47 （ 8 ）： 562 - 575 .

张立平，张立杰，袁晓明等 . 基于静力等承载强度的T型接头角焊缝焊脚尺寸确定及疲劳特性［J］. 电焊机， 2023 ， 53 （ 11 ）： 96 - 100 .

ZHANG L P ， ZHANG L J ， YUAN X M ， et al . Determination of Fillet Weld Leg Size and Fatigue Characteristics for T-Joints Based on Static Equal Load-Carrying Strength ［J］. Electric Welding Machine ， 2023 ， 53 （ 11 ）： 96 - 100 .

郭军礼 . 基于等承载原则的低匹配角焊缝焊接接头设计［D］. 黑龙江：哈尔滨工业大学， 2021 .

GUO J L . Welded Joint Design for Low-Match Fillet Welds Based on the Equal Load-Carrying Principle ［D］. Heilongjiang ： Harbin Institute of Technology ， 2021 .

Standard Methods for Mechanical Testing of Welds： A WS B4.0M-2007 ［S］.