外加磁场对高强不锈钢电阻点焊熔核组织与性能调控技术研究

徐野; 叶结和; 李卓然; 夏裕俊; 李永兵; 韩晓辉

doi:10.7512/j.issn.1001-2303.2024.09.07

轨道车辆高性能焊接制造 | 浏览量 : 0 下载量: 7 CSCD: 0

PDF
导出
分享
收藏
专辑

外加磁场对高强不锈钢电阻点焊熔核组织与性能调控技术研究
Study on the Control Technology of Microstructure and Properties of High Strength Stainless Steel Resistance Spot Welding by Applied Magnetic Field
2024年54卷第9期页码：55-62
纸质出版日期： 2024-09-25 ，
DOI： 10.7512/j.issn.1001-2303.2024.09.07
稿件说明：

移动端阅览

徐野，叶结和，李卓然，等.外加磁场对高强不锈钢电阻点焊熔核组织与性能调控技术研究［J］.电焊机，2024，54（9）：55-62.

XU Ye, YE Jiehe, LI Zhuoran, et al.Study on the Control Technology of Microstructure and Properties of High Strength Stainless Steel Resistance Spot Welding by Applied Magnetic Field[J].Electric Welding Machine, 2024, 54(9): 55-62.
徐野，叶结和，李卓然，等.外加磁场对高强不锈钢电阻点焊熔核组织与性能调控技术研究［J］.电焊机，2024，54（9）：55-62. DOI： 10.7512/j.issn.1001-2303.2024.09.07.

XU Ye, YE Jiehe, LI Zhuoran, et al.Study on the Control Technology of Microstructure and Properties of High Strength Stainless Steel Resistance Spot Welding by Applied Magnetic Field[J].Electric Welding Machine, 2024, 54(9): 55-62. DOI： 10.7512/j.issn.1001-2303.2024.09.07.

摘要

针对轨道车辆高强不锈钢材料电阻点焊存在的压痕明显、熔核直径波动较大、熔核中心缩孔等问题，探索了磁控电阻点焊技术对提升焊接质量和接头性能的潜力。通过在现有电阻点焊设备上增加环形永磁体，利用外加磁场对熔融金属进行电磁搅拌，发现磁控电阻点焊能够显著改善焊点质量和接头性能。与传统电阻点焊相比，磁控点焊可降低凸痕高度80.6%，增大熔核直径12.0%，并将熔核等轴晶区的枝晶间比例从29%改善至6%。此外，磁控点焊接头的拉剪断裂载荷提高11.8%，疲劳强度也得到了提升。通过微观组织观测发现，磁控点焊能够有效细化熔核晶粒，使枝晶间比例大幅下降，从而提高接头表面强度，降低压痕深度。疲劳试验结果表明，磁控点焊接头的疲劳寿命显著提高，且断裂模式由传统点焊的界面断裂转变为高韧性的纽扣断裂模式。研究为磁控电阻点焊技术在不锈钢轨道车辆制造中的应用提供了实验数据支持，并为无涂装车辆高可靠无痕点焊提供了借鉴。

Abstract

This study explores the potential of magnetic resistance spot welding technology to improve the welding quality and joint performance of high-strength stainless steel materials for railway vehicles

which are prone to problems such as prominent indentation

large fluctuations in nugget diameter

and shrinkage holes in the center of the nugget. By adding annular permanent magnets to existing resistance spot welding equipment and utilizing the electromagnetic stirring effect of the external magnetic field on the molten metal

magnetic resistance spot welding was found to significantly improve the quality of the weld and joint performance. Compared to traditional resistance spot welding

magnetic spot welding can reduce indentation height by 80.6%

increase nugget diameter by 12.0%

and improve the dendrite proportion in the isometric zone of the nugget from 29% to 6%. Additionally

the tensile shear fracture load of the magnetic spot welded joints is increased by 11.8%

and fatigue strength is also enhanced. Microstructure observations reveal that magnetic spot welding can effectively refine the nugget grains

significantly reduce the dendrite proportion

thereby improving the surface strength of the joint and reducing indentation depth. Fatigue test results show that the fatigue life of magnetic spot welded joints is significantly improved

and the fracture mode changes from the interfacial fracture of traditional spot welding to a high-toughness button fracture mode. This study provides experimental data support for the application of magnetic resistance spot welding technology in the manufacturing of stainless steel railway vehicles and offers valuable references for the high-reliability and mark-free spot welding of unpainted vehicles.

关键词

磁控电阻点焊高强不锈钢轨道车辆力学性能焊接质量

Keywords

magnetic resistance spot weldinghigh strength stainless steelrailway vehiclesmechanical propertieswelding quality

references

叶结和，李振江. 轨道车辆不锈钢电阻点焊工艺试验［J］. 电焊机，2015，45（1）：137-140.

YE Y H，LI Z J. Process test of stainless steel resistance spot welding for rail vehicles［J］. Electric Welding Machine，2015，45（1）：137-140.

康丽齐. 不锈钢轨道车辆焊接技术应用［J］. 电焊机，2017，47（10）：86-88.

KANG L Q.Application of stainless steel rail vehicle welding technology［J］. Electric Welding Machine，2017，47（10）：86-88.

康丽齐，邵有发，魏良，等. 电阻点焊在不锈钢轨道车辆上的应用研究［J］. 电焊机，2018，48（3）：349-353.

KANG L Q，SHAO Y F，WEI L，et al. Research on the application of resistance spot welding in stainless steel rail vehicles［J］ Electric Welding Machine，2018，48（3）：349-353.

Watanabe Y，Takeda T，Sato H. Effect of magnetic field on weld zone by spot welding in stainless steel［J］. ISIJ International，2006，46：1292-1296.

Han X，Xu Y，Guo S，et al. Numerical analysis of the effect of electrode strips on spot-welding process［J］. Key Engineering Materials，2020，837：58-63.

韩晓辉，赵延强，刘伟，等. 高速列车不锈钢车体点焊接头疲劳断裂分析及疲劳性能对比研究［J］. 焊接，2013（8）：33-36.

HAN X H，Zhao Y Q，LIU W，et al. Comparison of fatigue property and analysis on spot welded joint of stainless steel body in high speed train［J］. Welding，2013（8）：33-36.

林忠钦，马运五，夏裕俊，等. 载运工具高性能薄壁承载结构成形及连接工艺研究进展［J］. 机械工程学报，2023，59（20）：1-17.

LIN Z Q，MA Y W，XIA Y J，et al. Advances in Forming and Joining Processes of Lightweight High-strength Thin-walled Vehicle Structures［J］. Journal of Mechanical Engineering，2023，59（20）：1-17.

李永兵，马运五，楼铭，等.轻量化薄壁结构点连接技术研究进展［J］.机械工程学报，2020，56（06）：125-146.

LI Y B，MA Y W，LOU M，et al. Advances in Spot Joining Technologies of Lightweight Thin-walled Structures［J］. Journal of Mechanical Engineering，2020，56（06）：125-146.

Li Z R，Zhang D P，Chen R M，et al. Improving Weldability of Press Hardened Steel Through Combining Stepped Current Pulse and Magnetically Assisted Resistance Spot Welding Process［J］. Journal of Manufacturing Science and Engineering，2024，146（2）：021007.

尹月. 外加直流磁场对超细晶粒钢点焊质量的影响［D］. 黑龙江：哈尔滨工业大学，2009.

YIN Y. Influence of external DC magnetic field on spot welding quality of ultrafine grain steel［D］. Heilongjiang： Harbin Institute of Technology，2009.

沈琦，李永兵，陈关龙，等. 永磁体磁场对双相高强钢电阻点焊质量的影响［J］. 焊接学报，2011，32（4）：21-24.

SHEN Q，LI Y B，CHEN GL，et al. Effect of permanent magnetic field on quality of two-phase high-strength rigid-resistance spot welding［J］. Transactions of The China Welding Institution，2011，32（4）：21-24.

沈琦. 高强钢磁控电阻点焊机理与工艺方法研究［D］. 上海：上海交通大学，2012.

SHEN Q. Study on mechanism and technology of magnetron resistance spot welding of high strength stee［D］.Shanghai：Shanghai Jiao Tong University，2012.

彭乃康. 外加交变磁场对超细晶粒钢点焊质量的影响［D］.黑龙江：哈尔滨工业大学，2010.

PENG N K. Effect of alternating magnetic field on spot welding quality of ultrafine grain steel［D］. Heilon gjinag：Harbin Institute of Technology，2010.

GB/T 43412-2023，金属薄板电阻点焊推荐工艺规范［S］. 北京：中国标准出版社，2023.

文章被引用时，请邮件提醒。

提交

不同强度匹配对X80管线钢环焊缝抗氢致裂纹性能的影响研究

轨道车辆铝合金长大薄壁脉冲复合磁控高效弧焊工艺研究

Al-Mg-Sc-Zr高强铝合金电弧增材修复工艺及组织性能研究

ERNiCrMo-3焊丝组织性能及内部织构研究

1 000 MPa级高强钢国产自研实心焊丝焊接工艺研究