焊接道数和层间温度对5083铝合金多道焊对接接头焊接残余应力和变形的影响

廖娟; 程鹏; 陈庆顺; 汤小瑞; 邱波

doi:10.7512/j.issn.1001-2303.2023.11.12

焊接工艺 | 浏览量 : 0 下载量: 18 CSCD: 0

PDF
导出
分享
收藏
专辑

焊接道数和层间温度对5083铝合金多道焊对接接头焊接残余应力和变形的影响
Effects of Welding Pass Number and Interlayer Temperature on Welding Residual Stress and Deformation of 5083 Al Alloy Multi-pass Butt Joint
2023年53卷第11期页码：77-83
收稿：2023-04-18，

修回：2023-05-15，

纸质出版：2023-11-25
DOI： 10.7512/j.issn.1001-2303.2023.11.12
稿件说明：

移动端阅览

廖娟，程鹏，陈庆顺，等.焊接道数和层间温度对5083铝合金多道焊对接接头焊接残余应力和变形的影响［J］.电焊机，2023，53（11）：77-83. DOI： 10.7512/j.issn.1001-2303.2023.11.12.

LIAO Juan, CHENG Peng, CHEN Qingshun, et al.Effects of Welding Pass Number and Interlayer Temperature on Welding Residual Stress and Deformation of 5083 Al Alloy Multi-pass Butt Joint[J].Electric Welding Machine, 2023, 53(11): 77-83. DOI： 10.7512/j.issn.1001-2303.2023.11.12.

摘要

以5083铝合金多道焊对接接头为研究对象，构建了其热-冶金-力学耦合的三维有限元模型，在考虑相变情况下，对两道焊的焊接过程温度场、残余应力分布和变形进行数值计算与分析，并将结果与试验数据进行对比，验证了该模型的准确度。分析了焊接道数和层间温度对焊接残余应力分布以及焊接变形的影响规律，结果表明：随着焊接道数的增加，纵向残余应力逐渐增加，焊接道数对横向残余应力几乎无影响，焊接变形逐渐增加；随着层间温度的升高，纵向残余应力逐渐降低，横向残余应力先减小后增大，但层间温度对焊接变形几乎无影响，可采用100 ℃作为最佳层间温度进行焊接。

Abstract

A three-dimensional finite element model of thermal-metallurgical-mechanical coupling was established for investigating the multi-pass welded butt joints of 5083 aluminum

considering phase transformation

to simulate and analyze the temperature field during welding process

residual stress distribution and deformation of two-pass welding . The accuracy of the model was verified by comparison with experimental results. In addition

the influence of the number of welding passes and interlayer temperature on residual stress distribution and deformation were anlyzed. The results showed that

as the number of welding passes increases

the longitudinal residual stress gradually increases

the number of welding passes has almost no effect on the transverse residual stress

and the welding deformation gradually increases; as the interlayer temperature increases

the longitudinal residual stress gradually decreases

while the transverse residual stress first decreases and then increases

the interlayer temperature has almost no effect on welding deformation. The optimum interlayer temperature of 100℃ can be used for welding.

关键词

Keywords

references

SAESSI M ， ALIZADEH A ， ABDOLLAHI A . Wear behavior and dry sliding tribological properties of ultra-fine grained Al5083 alloy and boron carbide-reinforced A15083-based composite at room and elevated temperatures ［J］. Transactions of Nonferrous Metals Society of China ， 2021 ， 31 ： 74 - 91 .

杜文普，钮旭晶，郁志凯，等 . 6005A-T6铝合金车钩面板多层多道焊残余应力与变形规律的数值分析［J］. 电焊机， 2018 ， 48 （ 03 ）： 120 - 124 .

DU W P ， NIU X J ， YU Z K ， et al . Numerical simulation on residual stress and deformation of multi-pass welding of 6005A-T6 aluminum alloy coupler panel ［J］. Electric Welding Machine ， 2018 ， 48 （ 03 ）： 120 - 124 .

Genchev G ， Doynov N ， Ossenbrink R ， Michailov V ， Bokuchava G ， Petrov P . Residual stresses formation in multi-pass weldment： a numerical and experimental study ［J］. Journal of Constructional Steel Research ， 2017 ， 138 ： 633 - 641 .

Xu S ， Wang W . Numerical investigation on weld residual stresses in tube to tube sheet joint of a heat exchanger ［J］. International Journal of Pressure Vessels and piping ， 2013 ， 101 ： 37 - 44 .

CAÑAS J ， PICÓN R ， PARÍS F ， et al . Experimental and numerical analysis of residual stresses in welded Al 5083-O aluminum plates ［J］. Welding International ， 1994 ， 8 （ 1 ）： 30 - 35 .

CAÑAS J ， PICÓN R ， PARÍS F ， et al . A simplified numerical analysis of residual stresses in aluminum welded plates ［J］. Computers and Structures ， 1996 ， 58 （ 1 ）： 59 - 69 .

CHENG C M . Butt-welding residual stress of heat treatable aluminum alloy ［J］. Journal of Materials Science and Technology ， 2007 ， 23 （ 2 ）： 217 - 222 .

Lu Y H ， Zhu S C ， Zhao Z T ， et al . Numerical simulation of residual stresses in aluminum alloy welded joints ［J］. Journal of Manufacturing Processes 2020 ， 50 ： 380 - 393 .

廖娟，凌泽民，彭小洋 . 考虑相变的铝合金管焊接残余应力数值模拟［J］. 材料工程， 2013 （ 4 ）： 34 - 38 .

LIAO J ， LING Z M ， PENG X Y . Numerical simulation of residual Stresses for aluminum alloy pipe incorporating metallurgical phase transformation ［J］. Journal of Materials Engineering ， 2013 （ 4 ）： 34 - 38 .

宁佶 . 层间冷却对多道焊厚板残余应力及变形的影响［J］. 实验室研究与探索， 2021 ， 40 （ 9 ）： 39 - 42 .

NING J . Effect of interlayer cooling on residual stress and deformation of multi pass welding thick plate ［J］. Research and Exploration in Laboratory ， 2021 ， 40 （ 9 ）： 39 - 42 .

GOLADK J ， CHAKRAVARITI A ， BIBBY M . A new finite element model for welding heat sources ［J］. Metallurgical and Materials Transactions B ， 1984 ， 15 （ 2 ）： 299 - 305 .

SCHAJER G S . Measurement of non-uniform residual stresses using the hole-drilling method. Part I—Stress calculation procedures ［J］. Journal of Engineering Materials and Technology ， 1988 ， 110 （ 4 ）： 338 - 343 .

SCHAJER G S . Measurement of non-uniform residual stresses using the hole-drilling method. Part Ⅱ—practical application of the integral method ［J］. Journal of Engineering Materials and Technology ， 1988 ， 110 （ 4 ）： 344 - 349 .

宋丽平 . 模拟焊接道数对压力容器残余应力及变形的影响［J］. 热加工工艺， 2012 ， 41 （ 07 ）： 130 - 132 .

SONG L P . Effects of Simulation Welding Passes on Pressure Vessel's Residual Stress and Deformation ［J］. Hot Working Technology ， 2012 ， 41 （ 07 ）： 130 - 132 .

编辑部网址： http：//www.71dhj.com http://www.71dhj.com