Microstructure and Properties of Inconel 718 Alloy Additively Manufactured by Double Pulsed TIG with Stepped Filling Wire

ZHANG Cheng; ZHANG Gang; LIU Zhongyi; SHI Yu; WEI Tao

doi:10.7512/j.issn.1001-2303.2025.07.03

Important Issuse | Views : 0 下载量: 12 CSCD: 0

PDF
Export
Share
Collection
Album

Microstructure and Properties of Inconel 718 Alloy Additively Manufactured by Double Pulsed TIG with Stepped Filling Wire
Vol. 55, Issue 7, Pages: 36-42(2025)
Received：06 May 2024，

Revised：2024-07-26，

Published：20 July 2025
DOI： 10.7512/j.issn.1001-2303.2025.07.03
稿件说明：

移动端阅览

张程,张刚,刘忠义,等.Inconel 718步进填丝双脉冲TIG电弧增材微观组织及性能[J].电焊机,2025,55(7):36-42. DOI： 10.7512/j.issn.1001-2303.2025.07.03.

ZHANG Cheng, ZHANG Gang, LIU Zhongyi, et al.Microstructure and Properties of Inconel 718 Alloy Additively Manufactured by Double Pulsed TIG with Stepped Filling Wire[J].Electric Welding Machine, 2025, 55(7): 36-42. DOI： 10.7512/j.issn.1001-2303.2025.07.03.

摘要

针对镍基高温合金TIG电弧增材存在组织及性能各向异性的共性难题，提出采用步进填丝双脉冲钨极氩弧焊（Double-Pulse-TIG，DP-TIG）方法开展了Inconel718镍基高温合金的增材制造试验，重点研究分析了高频脉冲电流振幅对增材件组织及性能的影响规律。利用红外热成像仪测量了熔池温度场，并结合电子背散射衍射（Electron Back Scatter Diffraction，EBSD）图像揭示了微观组织演变的内在热力学原因。通过拉伸试验表征了试件力学性能变化，并分析了断口形貌特征。研究结果表明：当高频脉冲电流幅值由20 A增加到100 A时，熔池温度梯度

减小，熔池凝固速率

增大，凝固参数

G×R

和

都减小，组织向等轴晶方向转变；平均晶粒大小由56.2 μm减小到49.7 μm，在

001

方向上的取向密度从21.16增加到28.32；横向抗拉强度基本保持不变，约为740 MPa；纵向抗拉强度由729 MPa增加到756 MPa。高频脉冲电流幅值调控可以弱化增材件各

向异性，横纵向塑韧性明显改善增强。

Abstract

Aiming at solving the anisotropy of microstructure and properties commonly existing in traditional arc welding

the component of Inconel 718 was additive manufactured by double-pulse-TIG (DP-TIG). The influence by the amplitude of high frequency pulse current on the microstructure and properties of the components is specially studied. The temperature field of molten pool was got by infrared thermal imager

and the thermodynamic reasons of microstructure evolution were revealed by Electron Back Scatter Diffraction (EBSD). The mechanical properties of the samples were characterized by tensile test

and the fracture morphology was analyzed. The results show that when the amplitude of high frequency pulse increases from 20 A to 100 A

the temperature gradient

of molten pool decreases

the solidification rate

of molten pool increases

the solidification parameters

G×R

and

decrease

and the microstructure changes to equiaxed crystal; The average grain size decreased from 56.2 μm to 49.7 μm

and the orientation density on the

001

direction increased from 21.16 to 28.32; The horizonal tensile strength is about 740 MPa which is nearly constant. The vertical tensile strength increased from 729 MPa to 756 MPa. By controlling the amplitude of high frequency pulse current

the anisotropy of the components is weakened and the plasticity and toughness in both transverse and longitudinal directions is enhanced.

关键词

Keywords

references

潘坚，王家胜 . 航天专用材料发展趋势［J］. 中国航天， 2002 （ 9 ）： 41 - 45 .

PAN J ， WANG J S . Development of Special Space Materials ［J］. Aerospace China ， 2002 （ 9 ）： 41 - 45 .

王会阳，安云岐，李承宇，等 . 镍基高温合金材料的研究进展［J］. 材料导报， 2011 ， 25 （ S2 ）： 482 - 486 .

WANG H Y ， AN Y Q ， LI C Y ， et al . Research Progress of Ni-based Superalloys ［J］. Materials Reports ， 2011 ， 25 （ S2 ）： 482 - 486 .

孙暄，胡斌，熊智慧，等 . 航空航天领域用增材制造金属材料的研究进展［J］. 上海金属， 2024 （ 3 ）： 1 - 12 .

SUN X ， HU B ， XIONG Z H ， et al . Progress in Research on Additive Manufactured Metallic Materials Reserved for Aerospace Field ［J］. Shanghai Metals ， 2024 （ 3 ）： 1 - 12 .

田彩兰，陈济轮，董鹏，等 . 国外电弧增材制造技术的研究现状及展望［J］. 航天制造技术， 2015 （ 2 ）： 57 - 60 .

TIAN C L ， CHEN J L ， DONG P ， et al . Current State and Future Development of the Wire Arc Additive Manufacture Technology Abroad ［J］. Aerospace Manufacturing Technology ， 2015 （ 2 ）： 57 - 60 .

BHUJANGRAO T ， VEIGA F ， SUáREZ A ， et al . High-temperature mechanical properties of IN718 alloy： Comparison of additive manufactured and wrought samples ［J］. Crystals ， 2020 ， 10 （ 8 ）： 689 .

CHEN F ， CAI X ， DONG B ， et al . Effect of process modes on microstructure and mechanical properties of CMT wire arc additive manufactured WE43 magnesium alloy ［J］. Journal of Materials Research and Technology ， 2023 ， 27 ： 2089 - 2101 .

张志强，李涵茜，贺世伟，等 . 激光与CMT-P电弧复合增材构件的微观组织特征研究［J］. 材料保护， 2023 ， 56 （ 10 ）： 74 - 82 .

ZHANG Z Q ， LI H Q ， HE S W ， et al . Study on Microstructure Characterization by Laser and CMT-P Arc Hybrid Additive Components ［J］. Materials Protection ， 2023 ， 56 （ 10 ）： 74 - 82 .

XU X ， DING J ， GANGULY S ， et al . Investigation of process factors affecting mechanical properties of INCONEL 718 superalloy in wire + arc additive manufacture process ［J］. Journal of Materials Processing Technology ， 2019 ， 265 ： 201 - 209 .

齐欢 . INCONEL 718（GH4169）高温合金的发展与工艺［J］. 材料工程， 2012 （ 08 ）： 92 - 100 .

QI H . Review of INCONEL 718 Alloy：Its History，Properties，Processing and Developing Substitutes ［J］. Journal of Materials Engineering ， 2012 （ 08 ）： 92 - 100 .

赵玉珍 . 焊接熔池的流体动力学行为及凝固组织模拟［D］. 北京：北京工业大学， 2004 .

ZHAO Y Z . The fluid dynamics behavior and solidification structure simulation of welding pool ［D］. Beijing ： Beijing University of Technology ， 2004 .

林鑫，杨海欧，陈静，等 . 激光快速成形过程中316L不锈钢显微组织的演变［J］. 金属学报， 2006 ， 42 （ 4 ）： 361 - 368 .

LIN X ， YANG H O . CHEN J， et al. Microstructure Evolution of 316L Stainless Steel During Laser Rapid Forming［J］. Acta Metallurgica Sinica ， 2006 ， 42 （ 4 ）： 361 - 368 .

LIU K ， YAN Z ， WANG F ， et al . Microstructure， texture and mechanical properties of Inconel GH4169 superalloy fabricated by wire arc additive manufacturing with arc oscillation ［J］. Journal of Alloys and Compounds ， 2023 ， 952 ： 170070 .

HONGMAO C ， FENCHENG L ， GUANG Y ， et al . Microstructure and Tensile Property of Electromagnetic Stirring Assisted Laser Repaired Inconel718 Superalloy ［J］. Rare Metal Materials and Engineering ， 2018 ， 47 （ 10 ）： 2949 - 2956 .

Alert me when the article has been cited

提交

Effect of Solution Treatment on Properties of 254SMo Steel Welded Joint

Forming and Properties of 304 Stainless Steel Joints by Local Dry Underwater Laser Welding

Microstructure and Mechanical Properties of Resistance Spot Welding Joints Between Magnesium/Galvanized Steel Dissimilar Metals

Study on Corrosion Performance Evaluation of Additively Manufactured P280GH Carbon Steel for Nuclear Power Applications

Effect of Deposition Current on Microstructure and Mechanical Properties of Wire-Arc Additive Manufactured 316H/AFA Steel