Effect of Scanning Path on Microorganization of Hot Wire Laser Repair K4169 Nickel-based Superalloy

KANG Guorong; SHI Yu; LI Chunkai; GU Yufen

doi:10.7512/j.issn.1001-2303.2025.02.07

Laser Technology and Application Innovation | Views : 0 下载量: 0 CSCD: 0

PDF
Export
Share
Collection
Album

Effect of Scanning Path on Microorganization of Hot Wire Laser Repair K4169 Nickel-based Superalloy
Vol. 55, Issue 2, Pages: 70-76(2025)
Received：23 April 2024，

Revised：04 May 2024，

Published：20 February 2025
DOI： 10.7512/j.issn.1001-2303.2025.02.07
稿件说明：

移动端阅览

康国荣，石玗，李春凯，等.扫描路径对热丝激光修复K4169镍基高温合金显微组织的影响［J］.电焊机，2025，55（2）：70-76. DOI： 10.7512/j.issn.1001-2303.2025.02.07.

KANG Guorong, SHI Yu, LI Chunkai, et al.Effect of Scanning Path on Microorganization of Hot Wire Laser Repair K4169 Nickel-based Superalloy[J].Electric Welding Machine, 2025, 55(2): 70-76. DOI： 10.7512/j.issn.1001-2303.2025.02.07.

摘要

采用金相、XRD、SEM、EBSD等检测手段研究非连续纵向与连续横向两种扫描路径对热丝激光修复K4169镍基高温合金显微组织的影响。结果表明：（1）两种扫描路径下修复区显微组织都以柱状树枝晶和少量等轴晶为主，但非连续纵向扫描路径下修复区各位置晶体尺寸均较小；（2）相组成都是γ-Ni基体相且都析出了有害相Laves相，但非连续纵向扫描路径下析出的Laves相的尺寸小、含量少；（3）非连续纵向扫描路径下的二次枝晶间距、晶粒平均尺寸更小，但该扫描路径下修复区小角度晶界含量高，会造成材料的塑性和韧性较差。

Abstract

The effects of discontinuous longitudinal and continuous transverse scanning paths on the microstructure of K4169 nickel-based superalloy repaired by hot wire laser were investigated by means of metallographic

XRD

SEM and EBSD. The results show that : (1) The microstructure of the repair zone under the two scanning paths is dominated by columnar dendrites and a small amount of equiaxed crystals

but the crystal size at each position of the repair zone under the discontinuous longitudinal scanning path is small. (2) The phase composition is γ-Ni matrix phase and the harmful phase Laves phase is precipitated

but the size of Laves phase is small and the content is small under the discontinuous longitudinal scanning path. (3) The secondary dendrite spacing and the average grain size are smaller under the discontinuous longitudinal scanning path

but the content of small angle grain boundaries in the repair zone is higher under this scanning path

which will cause poor plasticity and toughness of the material.

关键词

Keywords

references

许章华，谢志雄，康茂东，等 . K4169高温合金铸件铸造缺陷修复及疲劳性能研究［J］. 材料导报， 2021 （ 22 ）： 22115 - 22120 .

XU Z H ， XIE Z X ， KANG M D ， et al . Study of Casting Defect Repair and Fatigue Performance of K4169 Superalloy Casting ［J］. Materials Reports ， 2021 （ 22 ）： 22115 - 22120 .

李丛辰，陈文静，向超，等 . EA4T钢表面激光熔覆Fe314合金熔覆层的微观组织及性能［J］. 电焊机， 2016 ， 46 （ 05 ）： 73 - 77 .

LI C C ， CHEN W J ， XIANG C ， et al . Microstructure and properties of Fe314 alloy cladding layer by laser cladding on EA4T steel ［J］. Electric Welding Machine ， 2016 ， 46 （ 05 ）： 73 - 77 .

Salminen A . The filler wire-laser beam interaction during laser welding with low alloyed steel filler wire ［J］. Mechanika ， 2010 ， 84 （ 4 ）： 67 - 74 .

Nurminen J ， Riihimaki J ， Nakki J . Hot-wire cladding process studies ［C］// ICALEO ， 2007 ： 947 - 952 .

盛家锦 . 激光熔覆IN939镍基高温合金裂纹控制及热处理研究［D］. 浙江：浙江工业大学， 2021 ： 51 - 64 .

SHENG J J . Study of Crack Control and HeatTreatment of Laser Cladded IN939Nickel-based Superalloy ［D］. Zhejiang ： Zhejiang University of Technology ， 2021 ： 51 - 64 .

刘奋成，林鑫，杨高林，等 . 不同气氛激光立体成形镍基高温合金Inconel 718的显微组织和力学性能［J］. 金属学报， 2010 ， 46 （ 09 ）： 1047 - 1054 .

LIU F C ， LIN X ， YANG G L ， et al . Microstructures and Mechanical Properties of Laser Solid Formed Nickle base Superalloy INCONEL 718 Prepared in Different Atmospheres ［J］. Acta Metallurgica Sinica ， 2010 ， 46 （ 09 ）： 1047 - 1054 .

Su G X ， Shi Y ， Li G ， et al . Improving the deposition efficiency and mechanical properties of additive manufactured inconel 625 through hot wire laser metal deposition ［J］. Journal of Materials Processing Technology ， 2023 ， 322 ： 118175 .

Li P ， Yang T P ， Li S ， et al . Direct laser fabrication of nickel alloy samples ［J］. International Journal of Machine Tools and Manufacture ， 2005 ， 45 （ 11 ）： 1288 - 1294 .

汪旭东 . 激光功率对增材制造GH3039合金组织和力学性能影响［D］. 江西：南昌大学， 2022 ： 25 - 33 .

WANG X D . Effect of Laser Power on the Structure and Mechanical Properties of Additively Manufactured GH3039 Alloy ［D］. Jiangxi ： Nanchang University ， 2022 ： 25 - 33 .

Xu F J ， Lv Y H ， Liu Y X ， et al . Microstructural evolution and mechanical properties of Inconel 625 alloy during pulsed plasma arc deposition process ［J］. Journal of Materials Science and Technology ， 2013 ， 29 ： 480 - 488 .

Tanvir A N M ， Ahsan M R U ， Ji C W ， et al . Heat treatment effects on Inconel 625 components fabricated by wire + arc additive manufacturing （WAAM）—part 1： microstructural characterization ［J］. Int. J. Adv. Manuf. Technol. ， 2019 ， 103 ： 3785 - 3798 .

Kurz W ， Fisher D J . Dendrite growth in eutectic alloys： the coupled zone ［J］. International Materials Reviews ， 1979 （ 5-6 ）： 177 - 204 .

Alert me when the article has been cited

提交

Analysis and Improvement Measures for Strip Breakage in Laser Welding Joint of Cold-Rolled Strip Steel

Research on mechanical properties of higher heat input welded joints for super thick marine platform steels

Grain growth model of U75V rail steel and its application in welding