Mechanical Properties and Microstructure of Iron-nickel Based Alloy HT700P Welded Joint

DIAO Wangzhan; ZHANG Song; WANG Ping; XU Xiangjiu; HUANG Chao; LI Xiaofeng

doi:10.7512/j.issn.1001-2303.2024.10.06

“Huaguang”Cup Excellent Thesis Recommendation | Views : 0 下载量: 1303 CSCD: 0

PDF
Export
Share
Collection
Album

Mechanical Properties and Microstructure of Iron-nickel Based Alloy HT700P Welded Joint
Vol. 54, Issue 10, Pages: 53-60(2024)
Received：29 August 2024，

Published：25 October 2024
DOI： 10.7512/j.issn.1001-2303.2024.10.06
稿件说明：

移动端阅览

刁旺战，张松，王萍，等.铁镍基合金HT700P焊接接头力学性能和微观组织研究［J］.电焊机，2024，54（10）：53-60. DOI： 10.7512/j.issn.1001-2303.2024.10.06.

DIAO Wangzhan, ZHANG Song, WANG Ping, et al.Mechanical Properties and Microstructure of Iron-nickel Based Alloy HT700P Welded Joint[J].Electric Welding Machine, 2024, 54(10): 53-60. DOI： 10.7512/j.issn.1001-2303.2024.10.06.

摘要

采用机械TIG焊方法对铁镍基合金HT700P大口径管的环缝焊接，焊后进行稳定化热处理（980 ℃/3 h/AC）和无损检测（100%PT+100%RT+100%PAUT），合格后对焊接接头进行拉伸强度、弯曲、硬度性能、冲击、高温持久性能和微观金相组织试验。试验结果表明：焊接接头室温抗拉强度、屈服强度高于HT700P母材的下限值，弯曲试验合格。焊接接头中母材和热影响区的硬度明显大于焊缝，母材和热影响区硬度无明显差别。焊缝的室温冲击平均值为160.7 J，热影响区的室温冲击平均值为102.3 J，均高于HT700P母材的下限值。焊接接头10

小时持久断裂强度为138.3 MPa。焊接接头宏观和微观金相组织检验合格，焊缝金相组织均为奥氏体，不存在TCP等有害相的析出。

Abstract

The mechanical TIG was used to weld the large diameter pipe ring seam of iron-nickel based alloy HT700P. After the welding and stabilization heat treatment (980 ℃/3 h/AC) was qualified by non-destructive testing (100% PT+100% RT+100% PAUT)

the welded joint was subjected to tensile strength

bending

hardness performance

impact

high temperature endurance performance

and microstructure tests. The test results showed that the tensile strength and yield strength of the welded joint at room temperature were higher than the lower limit of the HT700P alloy

and the bending test was qualified. The hardness of the BM and HAZ in the welded joint is significantly higher than weld seam

while there is no significant difference in hardness between the base metal and heat affected zone. The average room temperature impact at the weld seam is 160.7 J

and at the HAZ is 102.3 J

both of which are higher than the lower limit of the HT700P alloy. The persistent strength of the welded joint for 10

hours is σ=138.3 MPa. The macro and micro metallographic structure of the welded joint is qualified

and the microstructure of the weld is austenite without the precipitation of harmful phases such as TCP.

关键词

Keywords

references

敬仕煜，何小明，张玮，等 . 650 ℃先进超超临界锅炉高温部件选材探讨［J］. 发电设备， 2023 ， 37 （ 5 ）： 310 - 316 .

JING S Y ， HE X M ， ZHANG W ， et al . Discussion on material selection for high-temperature components of advanced ultra-supercritical boilers at 650 ℃ ［J］. Power Generation Equipment ， 2023 ， 37 （ 5 ）： 310 - 316 .

刘正东，陈正宗，何西扣，等 . 630~700 ℃超超临界燃煤电站耐热管及其制造技术进展［J］. 金属学报， 2020 ， 56 （ 4 ）： 539 - 548 .

LIU Z D ， CHEN Z Z ， HE X K ， et al . Progress in heat-resistant tubes and their manufacturing technology for ultra-supercritical coal-fired power plants at 630~700 ℃ ［J］. Acta Metallurgica Sinica ， 2020 ， 56 （ 4 ）： 539 - 548 .

田志豪 . 700 ℃超超临界锅炉用617B镍基合金组织和性能研究［D］. 上海：上海交通大学， 2020 .

TIAN Z H . Study on the microstructure and properties of 617B nickel-based alloy for 700℃ ultra-supercritical boilers ［D］. Shanghai ： Shanghai JiaoTong University ， 2020 .

朱传志，袁勇，尹宏飞，等 . 超超临界机组用 Sanicro25耐热钢研究进展［J］. 材料导报， 2017 ， 31 （ 7 ）： 78 - 84 .

ZHU C Z ， YUAN Y ， YIN H F ， et al . Research progress on Sanicro25 heat-resistant steel for ultra-supercritical units ［J］. Materials Review ， 2017 ， 31 （ 7 ）： 78 - 84 .

中国科学院金属研究所 . GH984G合金性能数据手册［M］. 沈阳：金属研究所， 2017 .

西安热工研究院有限公司，中国华能集团有限公司 . HT700P先进超超临界电站高温部件用材料（管材）［Z］. 西安：西安热工研究院有限公司， 2021 .

Wang H Q ， Han K ， Peng F ， et al . Strain-age cracking in vacuum electron beam welded IN738LC alloy during post-weld heat treatment ［J］. Vacuum ， 2021 （ 194 ）： 1 - 11 .

2019 ASME Boiler and Pressure Vessel Code Part D Properties（Metric）［S］. USA ： The American Society of Mecha- nical Engineers ， 2019 .

李克俭，李晓刚，张宇，等 . 异种金属焊接接头微观组织演化及高温失效机理综述［J］. 电焊机， 2020 ， 50 （ 9 ）： 17 - 43 .

LI K J ， LI X G ， ZHANG Y ， et al . A review of microstructural evolution and high-temperature failure mechanism in dissimilar metal welded joints ［J］. Electric Welding Machine ， 2020 ， 50 （ 9 ）： 17 - 43 .

Soysal T ， Kou S ， Tat D ， et al . Macrosegregation in dissimilar-metal fusion welding ［J］. Acta Materialia ， 2016 ， 110 ： 149 - 160 .

KOU S . Welding metallurgy ［M］. 2nd ed . New Jersey ： John Wiley & Sons Inc. ， 2003 ： 20 - 36 .

Mandal P K ， Saji A M ， Lalu A K ， et al . Microstructural study and mechanical properties of TIG welded Inconel 617 superalloy ［J］. Materials Today：Proceedings ， 2022 ， 62 ： 3561 - 3568 .

刘岩岩，朱丽慧，周任远，等 . Inconel 617B 合金焊接接头 750 ℃持久微观组织演变对性能的影响［J］. 金属热处理， 2017 ， 42 （ 5 ）： 62 - 67 .

LIU Y Y ， ZHU L H ， ZHOU R Y ， et al . The effect of microstructural evolution on the properties of Inconel 617B alloy welded joints at 750 ℃ ［J］. Metal Heat Treatment ， 2017 ， 42 （ 5 ）： 62 - 67 .

Alert me when the article has been cited

提交

Forming and Properties of 304 Stainless Steel Joints by Local Dry Underwater Laser Welding

Microstructure and Mechanical Properties of High Nitrogen Austenitic Stainless Steel Welded Joints by Using Multi-strand Composite Welding Wire GMAW

Study on the Microstructure and Properties of Laser Wire Filling Welding and MAG Welding Joints of Ferritic Stainless Steel

Research on the Heat Treatment Microstructure and Mechanical Properties of Ti-6Al-4V Alloy Fabricated by Laser Arc Composite Additive Manufacturing

Research on the Microstructure and Mechanical Properties of 6082 Aluminum Alloy FSW Joints based on Welding Speed