Experimental Study on Laser Welding Stress and Deformation of Titanium Alloy Based on Synchronous Water Mist Cooling

GAO Qingsheng; ZHANG Wenliang; ZHUANG Mingxiang; YE Zetao; LIU Yongqiang; ZHAN Xiaohong

doi:10.7512/j.issn.1001-2303.2024.06.13

Welding Technology | Views : 0 下载量: 558 CSCD: 0

PDF
Export
Share
Collection
Album

Experimental Study on Laser Welding Stress and Deformation of Titanium Alloy Based on Synchronous Water Mist Cooling
Vol. 54, Issue 6, Pages: 80-86(2024)
Received：07 March 2023，

Revised：2023-11-06，

Published：25 June 2024
DOI： 10.7512/j.issn.1001-2303.2024.06.13
稿件说明：

移动端阅览

高庆生，章文亮，庄明祥，等.基于水雾在线冷却的钛合金激光焊接应力变形研究［J］.电焊机，2024，54（6）：80-86. DOI： 10.7512/j.issn.1001-2303.2024.06.13.

GAO Qingsheng, ZHANG Wenliang, ZHUANG Mingxiang, et al.Experimental Study on Laser Welding Stress and Deformation of Titanium Alloy Based on Synchronous Water Mist Cooling[J].Electric Welding Machine, 2024, 54(6): 80-86. DOI： 10.7512/j.issn.1001-2303.2024.06.13.

摘要

为解决TC4钛合金薄板激光焊接后因残余应力引起的变形问题，选用500 mm×50 mm×1.2 mm规格的TC4钛合金薄板作为研究对象，通过激光焊接并应用水雾在线冷却法进行同步冷却。保持激光功率、焊接速度、离焦量等焊接工艺参数一致，仅改变水雾压力，以研究不同冷却条件下的应力变形控制效果。结果表明，在水雾压力为0.4 MPa、激光功率800 W、焊接速度1.3 m/min、离焦量0 mm的条件下，与自然冷却相比，焊后残余应力降低了29%，最大纵向挠曲变形量减少17.6%；水雾冷却下的焊缝组织尺寸更细小，分布更规整有序。试验证明，水雾在线冷却法能有效改善TC4钛合金薄板激光焊接后的残余应力和变形问题，还可以促进马氏体相变，使焊缝的网篮状组织更加规整有序，从而提升接头的力学性能。

Abstract

In this paper

the TC4 titanium alloy sheet with a specification of 500mm×50mm×1.2mm is taken as the research object. In order to solve the problem of deformation caused by residual stress after laser welding

a Synchronous water mist cooling method is used to synchronously cool the rear of the heat source during the welding process. The effectiveness of this method was verified by measuring and comparing the deformation and stress levels before and after welding.The test shows that the deformation and residual stress of the specimen obtained by synchronous water mist cooling are greatly improved compared with those obtained by natural cooling under the same welding process parameters. Compared with the test results under different water mist pressures

when the water mist pressure is 0.4MPa

the laser power is 800W

the welding speed is 1.3m/min

and the defocus amount is 0mm

the residual stress after welding can be reduced by 29% compared with Free cooling

and the maximum longitudinal deflection can be reduced by 17.6%.Moreover

by observing the microstructure of the weld

it can be seen that the size of the weld net basket structure under the synchronous water mist cooling is smaller and the distribution is more orderly

indicating that the water mist cooling has a certain refining effect on the microstructure and can improve the mechanical properties of the welded joint.

关键词

Keywords

references

孙文君，王善林，陈玉华，等 . 钛合金先进焊接技术研究现状［J］. 航空制造技术， 2019 ， 62 （ 18 ）： 64 - 72 .

SUN W J ， WANG S L ， CHEN Y H ， et al . Development of advanced welding technologies for titanium alloys ［J］. Aviation Manufacturing Technology ， 2019 ， 62 （ 18 ）： 64 - 72 .

黄瑞生，方乃文，武鹏博，等 . 厚壁钛合金熔化焊接技术研究现状［J］. 电焊机， 2022 ， 52 （ 6 ）： 10 - 24 .

HUANG R S ， FANG N W ， WU P B ， et al . Research Status of Thick Plate Titanium Alloy Fusion Welding Technology ［J］. Electric Welding Machine ， 2022 ， 52 （ 6 ）： 10 - 24 .

刘西霞，尹存宏，刘维岗 . 基于随焊气体动态冷却方法的钛合金薄板激光焊接变形试验研究［J］. 热加工工艺， 2017 ， 46 （ 13 ）： 57 - 60 .

LIU X X ， YIN C H ， LIU W G . Experimental study on laser welding deformation of titanium alloy sheet based on synchronous gas cooling during welding ［J］. Hot Working Process ， 2017 ， 46 （ 13 ）： 57 - 60 .

黄亮 . TC4钛合金飞机壁板激光焊接工艺及残余应力研究［D］. 湖北：武汉理工大学， 2014 .

HUANG L . The technology and residual stress analysis of laser welding of TC4 titanium alloy ［D］. Hubei ： Wuhan University of Technology ， 2014 .

李菊 . 钛合金低应力无变形焊接过程机理研究［D］. 北京：北京工业大学， 2004 .

LI J . Studies on the mechanism of low stress no distortion welding for a titanium alloy ［D］. Beijing ： Beijing University of Technology ， 2004 .

梁岩，王孟君，王剑，等 . 焊前预热对康复器械用铝合金焊接残余应力的影响［J］. 电焊机， 2015 ， 45 （ 10 ）： 54 - 58 .

LIANG Y ， WANG M J ， WANG J ， et al . Effect of pre-heating on residual stress in aluminum alloy joint for healthcare applications ［J］. Electric Welding Machine ， 2015 ， 45 （ 10 ）： 54 - 58 .

关桥，张崇显 . 动态控制的低应力无变形焊接新技术［J］. 焊接学报， 1994 ， 15 （ 1 ）： 8 - 15 .

GUAN Q ， ZHANG C X . New technique for dynamically controlled low stress non-distorton welding ［J］. Journal of Welding ， 1994 ， 15 （ 1 ）： 8 - 15 .

李敬勇，章明明，李鹰，等 . 预拉伸对铝合金焊接残余应力和变形的影响［J］. 热加工工艺， 2005 （ 12 ）： 15 - 17 .

LI J Y ， ZHANG M M ， LI Y ， et al . Effect of pre-stretching on welding residual stress and deformations of aluminum alloy ［J］. Hot Working Process ， 2005 （ 12 ）： 15 - 17 .

王泽，邢玉明，刘鑫，等 . 振动环境下喷雾冷却的临界热流密度模型［J］. 航空动力学报， 2018 ， 33 （ 3 ）： 597 - 603 .

WANG Z ， XING Y M ， LIU X ， et al . Model of critical heat flux for spray cooling under vibration environment ［J］. Journal of Aerodynamics ， 2018 ， 33 （ 3 ）： 597 - 603 .

肖秀程 . 管线钢多弧埋弧焊随焊水雾激冷工艺研究［D］. 北京：机械科学研究总院， 2022 .

XIAO X C . Welding with local water mist cooling technology for multi-arc submerged arc welding of pipeline steel ［D］. Beijing ： China Academy of Machinery Science and Technology ， 2022 .

杨东旭 . TC4钛合金激光焊接接头溶质元素分布及不均匀性的研究［D］. 湖北：华中科技大学， 2017 .

YANG D X . Study on solute elements distribution and heterogeneity of microstructure and mechanical properties of TC4 alloy joints welded by fiber laser beam ［D］. Hubei ： Huazhong University of Science and Technology ， 2017 .

徐洁洁 . TC4钛合金激光焊接接头组织性能研究［D］. 北京：北京工业大学， 2009 .

XU J J . Research on microstructures and properties of laser welding joints of TC4 titanium alloy ［D］. Beijing ： Beijing University of Technology ， 2009 .

张宇鹏，丁来法， Valerii Bilous ，等 . 厚板TC4钛合金电子束焊接头组织演变及力学性能［J］. 电焊机， 2022 ， 52 （ 6 ）： 87 - 92 .

ZHANG Y P ， DING L F ， Valerii B ， et al . Microstructure Evolution and Mechanical Properties of Electron Beam Welded Joint of Thick Plate TC4 TitaniumAlloy ［J］. Electric Welding Machine ， 2022 ， 52 （ 6 ）： 87 - 92 .

方乃文，郭二军，徐锴，等 . 钛合金激光填丝焊缝晶粒生长及相变原位观察［J］. 中国有色金属学报， 2022 ， 32 （ 6 ）： 1665 - 1672 .

FANG N W ， GUO E J ， XU K ， et al . In-situ observation of grain growth and phase transformation in laser welding of titanium alloy with filler wire ［J］. The Chinese Journal of Nonferrous Metals ， 2022 ， 32 （ 6 ）： 1665 - 1672 .

方乃文，黄瑞生，谢吉林，等 . 大厚度TC4钛合金超窄间隙激光填丝焊接头组织性能研究［J］. 电焊机， 2022 ， 52 （ 6 ）： 25 - 34 .

FANG N W ， HUANG R S ， XIE J L ， et al . Study on properties and microstructures of large thickness TC4 titanium alloy welded joint by ultra-narrow gap laser welding using filler wire ［J］. Electric Welding Machine ， 2022 ， 52 （ 6 ）： 25 - 34 .

Alert me when the article has been cited

提交

Effect of Liquid Nitrogen Cooling on Microstructure, Residual Stress and Deformation of TC4 Titanium Alloy Laser Welding

Study on the Effects of X-Groove Geometric Parameters on Post-Welding Deformation and Residual Stress of 800MPa Grade Marine High-Strength Steel in MIG Welding

Misalignment Adaptability of TC4 Titanium Alloy Thin Plate Bottom-locking Joint Using Laser Welding

Finite Element Analysis of Bottom Welds of High Strength Steel CO2 Welding

Study on Temperature Field and Deformation of Double Electron Beam Welding of Intermediate Case of Aero Engine