Determination of Weld Leg Size and Fatigue Characteristics of T-joint Fillet Welds Based on Static Equal Bearing Strength

ZHANG Liping; ZHANAG Lijie; YUAN Xiaoming; LI Wen; PENG Genchen; YANG Fan

doi:10.7512/j.issn.1001-2303.2023.11.15

Welding Technology | Views : 0 下载量: 17 CSCD: 0

PDF
Export
Share
Collection
Album

Determination of Weld Leg Size and Fatigue Characteristics of T-joint Fillet Welds Based on Static Equal Bearing Strength
Vol. 53, Issue 11, Pages: 96-100(2023)
Received：13 July 2022，

Revised：2023-09-25，

Published：25 November 2023
DOI： 10.7512/j.issn.1001-2303.2023.11.15
稿件说明：

移动端阅览

张立平，张立杰，袁晓明，等.基于静力等承载强度的T型接头角焊缝焊脚尺寸确定及疲劳特性［J］.电焊机，2023，53（11）：96-100. DOI： 10.7512/j.issn.1001-2303.2023.11.15.

ZHANG Liping, ZHANAG Lijie, YUAN Xiaoming, et al.Determination of Weld Leg Size and Fatigue Characteristics of T-joint Fillet Welds Based on Static Equal Bearing Strength[J].Electric Welding Machine, 2023, 53(11): 96-100. DOI： 10.7512/j.issn.1001-2303.2023.11.15.

摘要

传统的角焊缝在焊脚尺寸设计时出于安全考虑，经常出现“过设计”现象，针对AWS D1.1《钢结构焊接规范》，GB50017—2017《钢结构设计规范》及DIN 18800《钢架结构》焊脚尺寸设计相关标准对比分析，各标准中关于不同板厚推荐的焊脚尺寸范围基本一致，但都仅推荐最大和最小焊脚尺寸，其选择范围较宽泛。基于上述分析，提出了一种基于静力等承载强度的焊缝尺寸确定方法。以一种T型接头为例，分别采用标准和静力等承载强度方法进行焊脚尺寸确定和计算。分析表明，对照标准确定的T型接头的焊脚尺寸为12 mm，而基于静力等承载强度计算确定的焊脚尺寸为9.91 mm，相比标准确定的尺寸减小了17.4%。通过ABAQUS和Fe-safe软件分别对接头进行静力计算和疲劳仿真分析，结果表明，与标准推荐的焊脚尺寸相比，通过静力等承载强度得到的焊脚尺寸承受的最大静力、疲劳寿命和失效位置均无明显变化，表明该焊缝尺寸确定方法具有合理性。

Abstract

For the sake of safety

the traditional fillet weld often has the phenomenon of "over designed" in the design of weld size. In view of the comparative analysis of the AWS D1.1 "Structural Welding Code -Steel"

GB50017 "Structural Design Code-Steel" and DIN 18800 "Steel Structure"

the recommended weld size ranges for different plate thicknesses were basically the same in each standard

but only the maximum and minimum weld sizes were recommended. It had a wide range of choices. Based on the above analysis

this paper proposed a method to determine the weld size based on static equal load-carrying strength. Taking a T-joint as an example

the standards and the static equal load-carrying strength theory were used to determine and calculate the weld size. The analysis showed that the weld size of T-joint was determined to be 12mm by using the standards

while the weld size was determined to be 9.91mm based on the calculation of static equal load-carrying strength theory

which was 17.4% less than the size determined by the standards. The static calculation and fatigue simulation analysis of the joint were carried out by ABAQUS and Fe-safe software respectively. The results showed that compared with the weld size recommended by the standards

the maximum static force

fatigue life and failure position of the weld size obtained by static equal load-carrying strength theory had no obvious changes

indicating that the method for determining the weld size was reasonable.

关键词

Keywords

references

季志水 . 关于T型接头焊脚尺寸大小的探讨［J］. 低碳世界， 2015 （ 23 ）： 266 - 267 .

JI Z S . Determination of fillet weld leg size of T-joint and analysis of fatigue characteristics ［J］. Low Carbon World ， 2015 （ 23 ）： 266 - 267 .

美国焊接学会（AWS）D1结构焊接委员会. A WS D1.1 钢结构焊接规范［S］. 四川：西南交通大学出版社， 2010 .

中华人民共和国住房和城乡建设部 . GB50017-2017 钢结构设计规范［S］. 北京：中国建筑工业出版社， 2017 .

美国钢结构学会 . ANSI/AI SC 360-10 美国建筑钢结构设计规范［S］. 北京：冶金工业出版社， 2010 .

聂春戈，孙振轩，孙彦彬，等 . 考虑疲劳性能的十字接头角焊缝尺寸设计［J］. 焊接学报， 2017 ， 38 （ 11 ）： 16 - 20 .

NIE C G ， SUN Z X ， SUN Y B ， et al . Size design of fillet weld of cruciform joint considering fatigue performance ［J］. Transactions of the China Welding Institution ， 2017 ， 38 （ 11 ）： 16 - 20 .

刘洋 . 关于角焊缝焊脚尺寸的选取［J］. 化工管理， 2016 （ 17 ）： 148 - 150 .

LIU Y . Selection of fillet weld leg size ［J］. Chemical Management ， 2016 （ 17 ）： 148 - 150 .

黄炼，黎清宁，屈婧婧，等 . 中厚板T形接头焊接顺序的模拟研究［J］. 电焊机， 2014 ， 44 （ 5 ）： 105 - 109 .

HUANG L ， LI Q N ， QU J J ， et al . Study of the welding sequences on T-joint of mid-thickness plate by simulation ［J］. Electric Welding Machine ， 2014 ， 44 （ 5 ）： 105 - 109 .

陈明刚，郭志栋，崔厚梅 . 焊脚尺寸的确定及其对伸臂焊接变形的影响［J］. 内燃机与配件， 2018 （ 22 ）： 89 - 90 .

CHEN M G ， GUO Z D ， CUI H M . Determination of welding leg size and its influence on welding deformation of the Outrigger ［J］. Internal Combustion Engine & Parts ， 2018 （ 22 ）： 89 - 90 .

Maddox S J . Status review on fatigue performance of fillet welds ［J］. Journal of Offshore Mechanics and arctic engineering ， 2008 ， 130 （ 3 ）： 31 - 36 ．

李金风，张东焕 . 基于折合应力正面角焊缝T形焊接接头的尺寸设计［J］. 焊接学报， 2017 ， 38 （ 1 ）： 43 - 46 .

LI J F ， ZHANG D H . Size design of T-shaped welded joint of front fillet weld based on reduced stress ［J］. Transactions of the China Welding Institution ， 2017 ， 38 （ 1 ）： 43 - 46 .

Alert me when the article has been cited

提交

Development and Process Test of a Local Dry Underwater Laser Welding Device

Application of Ultrasonic Testing Technology in Non-groove Weld Detection of Bogie Laser Arc Hybrid Welding

Study on Mechanical Properties of Dissimilar Metal Joints Between Haynes 230 and Inconel 617 Brazed with Amorphous BNi2 Filler Metal

Influence of Aging Treatment on Microstructure and Mechanical Properties of SLMed Ultra-high Strength Steel

Analysis of Process, Microstructure and Properties of Gas Metal Arc Welding with Rutile Flux-cored Wire for EH40 Steel