Temperature Field Analysis and Joint Microstructure of Laser Brazing of Galvanized Steel Sheet Based on CuSi3 Welding Wire

LIU Haijiang; WANG Qian; ZHANG Heng; LI Siliang

doi:10.7512/j.issn.1001-2303.2022.11.03

Important Issuse | Views : 0 下载量: 523 CSCD: 0

PDF
Export
Share
Collection
Album

Temperature Field Analysis and Joint Microstructure of Laser Brazing of Galvanized Steel Sheet Based on CuSi3 Welding Wire
Vol. 52, Issue 11, Pages: 14-21(2022)
Received：24 March 2022，

Revised：2022-09-24，

Published：25 November 2022
DOI： 10.7512/j.issn.1001-2303.2022.11.03
稿件说明：

移动端阅览

刘海江，汪乾，张恒，等.基于CuSi3焊丝的镀锌钢板激光钎焊温度场及接头组织分析［J］.电焊机，2022，52（11）：14-21. DOI： 10.7512/j.issn.1001-2303.2022.11.03.

LIU Haijiang, WANG Qian, ZHANG Heng, et al.Temperature Field Analysis and Joint Microstructure of Laser Brazing of Galvanized Steel Sheet Based on CuSi3 Welding Wire[J].Electric Welding Machine, 2022, 52(11): 14-21. DOI： 10.7512/j.issn.1001-2303.2022.11.03.

摘要

采用焊接试验与焊接数值仿真相结合的方法对镀锌钢板CuSi3焊丝激光钎焊焊接温度场进行研究，使用高斯面热源和旋转高斯体热模型构成的组合热源模型对温度场数值模型进行计算，根据试验和数值计算结果分析激光钎焊过程中焊接线能量对接头显微组织及温度场分布的影响规律。焊接接头母材区主要为尺寸均匀的细密等轴晶，而焊接热影响区主要为垂直于温度场等温线并朝向热源方向生长的柱状晶，柱状晶的宽度随着靠近热源在不断生长；随着焊接线能量的提升，焊接接头截面的钎缝深宽比也展现出增大的规律；表面焊缝中心温度场分布梯度较小，焊接线能量对焊缝中心峰值温度影响不大；焊缝边缘贴近母材区域温度在四种试验参数下均高于锌镀层沸点，从而导致焊接试件表面产生气孔。

Abstract

The welding temperature field of CuSi3 welding wire laser brazing of galvanized steel sheet was studied by combining welding experiment and welding numerical simulation. The combined heat source model composed of Gaussian surface heat source and rotating Gaussian body heat model was used to calculate the numerical model of the temperature field

and the effect of the welding line energy on the microstructure of the welded joint and the effect of temperature field distribution during the laser brazing process was analyzed according to the experimental and numerical calculation results. The experimental results show that the base metal BM (basic mental

BM) of the welded joint is mainly distributed as fine equiaxed grains with uniform size

while the HAZ (heat affect zone

HAZ) area is mainly distributed columnar grains that the growth direction is perpendicular to the temperature field isotherm and towards the heat source; with the increase of welding line energy

the aspect ratio of the welded joint also shows an increasing law; the temperature field distribution gradient in the center of the surface weld is small

and the welding line energy has little effect on the peak temperature of the weld center; the temperature of the weld edge close to the base metal is higher than the boiling point of the zinc coating under all parameters

which leads to the formation of holes on the surface of specimens.

关键词

Keywords

references

张屹，李时春，金湘中，等 . 镀锌钢板激光焊接关键技术研究［J］. 激光与光电子学进展， 2010 （ 07 ）： 33 - 41 .

ZHANG Y ， LI S C ， JIN X Z ， et al . Key Technology of Laser Welding of Galvanized Steel ［J］. Laser & Optoelectronics Progress ， 2010 （ 07 ）： 33 - 41 .

李斌，国莉，郭涟 . 激光钎焊在白车身中的应用［C］. 中国汽车工程学会. 2013中国汽车工程学会年会论文集 . 北京：北京理工大学出版社， 2013 ： 3 .

马凯 . 激光钎焊条件下CuSi3钎料与镀锌钢板界面传质行为的研究［D］. 上海：上海工程技术大学， 2015 .

MA K . Research of interface mass transfer behavior under the condition of laser brazing of Zinc-coated steel with CuSi3 filler metal ［D］. Shanghai ： Shanghai University of Engineering Science ， 2015 .

Min-Kyu Jeon ， Weon-Bae Kim ， Guk-Chan Han ， et al . A Study on Heat Flow and Temperature Monitoring in the Laser Brazing of a Pin-to-plate Joint ［J］. Journal of Material Processing Technology ， 1998 ， 82 （ 1-3 ）： 53 - 60 .

J. S. Park ， S. J. Na . Heat Transfer in a Stud-to-plate Laser Braze Considering Filler Metal Movement ［J］. Wel-ding Journal . 1998 ， 77 （ 4 ）： 155 - 163 .

赵振龙 . 轿车顶盖与侧围激光填丝焊接技术研究［D］. 吉林：吉林大学， 2012 .

ZHAO Z L . Research on the laser filler wire welding technology of the car roof and side panel ［D］. Jilin ： Jilin University ， 2012 .

宋永刚，梁国星，吕明 . 激光钎焊的温度场有限元分析［J］. 机械工程与自动化， 2009 （ 03 ）： 76 - 78 .

SONG Y G ， LIANG G X ， LV M . Finite Element Analysis of Temperature Field in Laser Brazing ［J］. Mechanical Engineering & Automation ， 2009 （ 03 ）： 76 - 78 .

封小松，陈彦宾，李俐群 . 镀锌板激光钎焊温度场的数值模拟［J］. 金属学报， 2006 （ 08 ）： 882 - 886 .

FENG X S ， CHEN Y B ， LI L Q . Temperature Filed Simulation of Laser Brazing for Galvanized Steel Sh-eets ［J］. Acta Metallurgica Sinica ， 2006 （ 08 ）： 882 - 886 .

冯杰 . 镀锌板激光钎焊温度场及应力应变场分析［D］. 黑龙江：哈尔滨工业大学， 2005 .

FENG J . The Analysis of Temperature field and Stress and Strain field in Laser Brazing of Galvanized Steel Sheet ［D］. Heilongjiang ： Harbin Institute of Technology ， 2005 .

金湘中，李力钧 . 激光深熔焊接过程中小孔效应的试验研究［J］. 应用激光， 1999 （ 05 ）： 293 - 295，322 .

JIN X Z ， LI L J . An Experimental Study on Keyhole Effect in Deep Penetration Laser Welding ［J］. Applied Laser ， 1999 （ 05 ）： 293 - 295，322 .

席明哲，虞钢 . 连续移动三维瞬态激光熔池温度场数值模拟［J］. 中国激光， 2004 ， 31 （ 12 ）： 1527 - 1532 .

XI M Z ， YU G . Numerical Simulation for the Transient Temperature Field of 3D Moving Laser Molten Pool ［J］. Chinese Journal of Lasers ， 2004 ， 31 （ 12 ）： 1527 - 1532 .

Reisgen U ， Schleser M ， Mokrov M ， et al . Optimization of laser welding of DP/TRIP steel sheets using statistical approach ［J］. Optics and Laser Technology ， 2012 ， 44 （ 1 ）： 255 - 262 .

LI L Q ， FENG X S ， CHEN Y B . Influence of laser energy input mode on joint interface characteristics in laser brazing with Cu-base filler metal ［J］. Transactions of Nonferrous Metals Society of China ， 2008 （ 05 ）： 1065 - 1070 .

Alert me when the article has been cited

提交

Effect of Laser Power on Temperature Field and Joint Microstructure and Properties in Laser-MIG Hybrid Welding of Q890 Steel

Effect of Heat Input Ratio on Residual Stress in Hybrid Laser-MIG Welded Joint

Microstructure and Mechanical Properties of CMT-Welded X80 Pipeline Steel Joints

Research on the Microstructure and Performance of Dual-layer Wear-resistant Alloy Steel Plate with Laser Cladding

Research on Crack Criterion based on Simulation Data of Brittle Temperature Zone of 690 Nickel-based Alloy Multilayer Multi-Pass Weld