Formation Behavior and Microstructure Analysis of Ni60 Laser Cladding Coating

SUN Yixiang; QIN Jian; ZHANG Lei; JING Peiyao; LIU Sheng; WANG Wei; ZHOU Litao

doi:10.7512/j.issn.1001-2303.2024.11.06

Overlaying and Surface Engineering | Views : 0 下载量: 9 CSCD: 0

PDF
Export
Share
Collection
Album

Formation Behavior and Microstructure Analysis of Ni60 Laser Cladding Coating
Vol. 54, Issue 11, Pages: 44-49(2024)
Published： 25 November 2024 ，
DOI： 10.7512/j.issn.1001-2303.2024.11.06
稿件说明：

移动端阅览

孙逸翔，秦建，张雷，等.Ni60激光熔覆涂层成形行为与微观组织分析［J］.电焊机，2024，54（11）：44-49.

SUN Yixiang, QIN Jian, ZHANG Lei, et al.Formation Behavior and Microstructure Analysis of Ni60 Laser Cladding Coating[J].Electric Welding Machine, 2024, 54(11): 44-49.
孙逸翔，秦建，张雷，等.Ni60激光熔覆涂层成形行为与微观组织分析［J］.电焊机，2024，54（11）：44-49. DOI： 10.7512/j.issn.1001-2303.2024.11.06.

SUN Yixiang, QIN Jian, ZHANG Lei, et al.Formation Behavior and Microstructure Analysis of Ni60 Laser Cladding Coating[J].Electric Welding Machine, 2024, 54(11): 44-49. DOI： 10.7512/j.issn.1001-2303.2024.11.06.

摘要

采用激光熔覆技术在Q235钢基体上制备Ni60涂层，探究了激光功率和熔覆速度对涂层成形质量及其微观组织的影响。结果表明，激光功率和熔覆速度改变了熔池温度和流动性，进而影响涂层表面成形质量和微观组织。随着激光功率的增加，涂层表面成形质量改善，缺陷减少，这主要归因于激光能量的增加促进了更充分的熔化和更好的熔池流动。此外，结合区的厚度随激光功率的增加先增大后降低。较低的熔覆速度有利于获得表面成形质量良好的涂层。然而，随着熔覆速度的提高，涂层中开始出现气孔等缺陷，这是由于熔池冷却速度过快，未能充分熔合所致；结合区的厚度未发生明显变化，其组织发生一定程度的松散和粗化。

Abstract

Ni60 coating was prepared on Q235 steel substrate by laser cladding. The effects of laser power and cladding speed on the forming quality and microstructure of the coatings were investigated. The results indicate that laser power and cladding speed change the temperature of the melt pool

and then affect the surface forming quality of the coating. With the increase of laser power

the surface forming quality of the coating increases and defects decrease. This is mainly attributed to the increase of laser energy which promotes the fuller melting and better melt pool flow. In addition

the thickness of the bonding zone increases first and then decreases with the increase of laser power. A lower melting speed is beneficial for obtaining coatings with good surface forming quality. However

as the melting rate increases

defects such as pores begin to appear in the coating

which is due to the rapid cooling rate of the melt pool and insufficient fusion. The thickness of the bonding zone has not changed significantly

and a certain degree of looseness and coarsening appear in the microstruture.

关键词

激光熔覆工艺参数成形质量微观组织

Keywords

laser claddingprocess parametersforming qualitymicrostructure

references

秦建，龙伟民，魏世忠，等. 激光钎涂金刚石的涂层形成行为及其机理分析［J］. 焊接学报，2022，45（3）：1-9.

QIN J，YANG J，LONG W M，et al. Research progress of additive technology of diamond and its composite materials［J］. Transactions of The China Welding Institution，2022，43（8）：102-112.

庞义斌，胡凤娇，张峰，等. 激光熔覆修复30CrMnSiA合金钢的显微组织和性能研究［J］. 电焊机，2023，53（1）：77-83.

PANG Y，HU F，ZHANG F，et al. Study on microstructure and properties of 30CrMnSiA alloy steel coating repaired by laser cladding［J］. Electric Welding Machine，2023，53（1）：77-83.

秦建，杨骄，龙伟民，等.金刚石及其复合材料增材技术研究进展［J］. 焊接学报，2022，43（08）：102-112.

QIN J，YANG J，LONG W M，et al. Research progress of additive technology of diamond and its composite materials［J］. Transactions of The China Welding Institution，2022，43（8）：102-112.

宋少东，王燕燕，舒林森，等. 基于NSGA-Ⅱ的Fe基合金激光熔覆工艺参数优化［J］. 电焊机，2021，51（12）：1-5.

SONG S D，WANG Y Y，SHU L S，et al. Optimization of laser cladding process parameters for Fe-based alloy based on NSGA-Ⅱ［J］. Eletric Welding Machine，2021，51（12）：1-5.

Ding L，Hu S，Quan X，et al. Effect of VN alloy addition on the microstructure and wear resistance of Co-based alloy coatings［J］. Journal of Alloys and Compounds，2016，659：8-14.

Srikrishna B R，Venkadeshwaran K. Research and development status of laser cladding on stainless steel alloys： Areview［J］. Materials Science Forum，2023，704：335-354.

Zhao Y，Guan C，Chen L，et al. Effect of process parameters on the cladding track geometry fabricated by laser cladding［J］. Optik-International Journal for Light and Electron Optics，2020，223：165447.

Liu X B，Meng X J，Liu H Q，et al. Development and characterization of laser clad high temperature self-lubricating wear resistant composite coatings on Ti-6Al-4V alloy［J］. Materials and Design，2014，55：404-409.

Adesina S O，Popoola API，Pityana L S，et al. A study on scan speed relationship with microstructural evolution， phase composition and microhardness of Ni-containing intermetallic coatings on Ti-6Al-4V using laser cladding technique［J］. Surface Review and Letters，2018，25（8）：1950035.

Okuno T，Kaneno Y，Yamaguchi T，et al. Processing parameter， microstructure and hardness of Ni base intermetallic alloy coating fabricated by laser cladding［J］. MRS Advances，2017，2（26）：1381-1386.

Long W，Liu D，Dong X，et al. Laser power effects on properties of laser brazing diamond coating［J］. Surface Engineering，2020，36：1315-1326.

Long W，Liu D，Wu A，et al. Influence of laser scanning speed on the formation property of laser brazing diamond coating［J］. Diamond and Related Materials，2020，110：108085.

Alert me when the article has been cited

提交

Spatial Behavior and Forming Analysis of Powder During Laser Cladding Process of Ni60/diamond Composite Coating

Comparison of Forming Quality, Microstructure and Properties of Four Types of Aluminum Alloy Components Fabricated by Wire and Arc Additive Manufacturing

Study on Microstructure Transformation and Mechanical Properties of Heat Affected Zone of Laser Cladding EA4T Steel

Key issues in laser cladding of tungsten carbide wear resistant materials

Study on the microstructure and properties of Fe-based amorphous composite coatings by different processes